Automotive Manual PDF

The AEM air bypass valve is ONLY compatible with genuine AEM intake systems. You must ensure that the valve is installed in the correct location for your vehicle and that the rubber soft mount that was originally supplied with the AEM intake is properly installed. The structural integrity of the valve depends on correct installation. Use of the AEM Air Bypass Valve in conjunction with any other system is neither recommended nor warranted and may result in, among other things, malfunction of the AEM Air Bypass Valve.
(more…)

Continue Reading Entry... »

By choosing the FOCUS 3-MODE remote you have opted for the User Friendly remote control solution. Made according to the highest quality, the FOCUS 3-MODE will provide you with long-term satisfaction. Please read these enclosed instructions carefully before putting your FOCUS 3-MODE to use.
Batteries
Your FOCUS 3-MODE Remote requires 2 new “AA/LR6″ Alkaline batteries.
1. Push and slide the battery door downwards and lift it up to remove it.
2. Match the batteries to the (+) and (–) marks inside the battery case, then insert the batteries.
3. Place the battery cover by sliding upwards and allowing it to click back into position.
- It is recommended that you do not use rechargeable batteries.
- On the inside of the battery compartment door you will find a label on which to write your Set-Up Codes for future reference.
(more…)

Continue Reading Entry... »

1. Check all parts. Read and understand instructions completely before beginning installation. Clean the under side of the frame. Clean out the weld nuts in the frame.
Parts List:
1) Hitch
6) 10mm - 1.25 x 40mm Hex Bolts
6) ł/₈” HD Flatwasher
6) 10mm Lockwashers
2. Remove the exhaust hangers and lower the exhaust to ease installation.
3. Remove the tow hook, four bolts on the passenger side. Remove the rear most bolt behind the tow hook. Return tow hook and bolts to vehicle owner.
(more…)

Continue Reading Entry... »

The AEM Cold Air Systems are 50 states Street Legal (some model and years still pending) and come with complete instructions for ease of installation. Our system is constructed of lightweight aluminum and then painted with a zirconia based powder coat for superior heat insulating characteristics. The aluminum will not crack in extended use like plastic and it is actually lighter than plastic. The tube diameter and length are matched for each engine to give power over a broad rpm range. Unlike the plastic systems that use a continually diverging cross section, we take advantage of the acoustical energy in the duct to promote cylinder filling during the intake valve-opening event.
(more…)

Continue Reading Entry... »

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 1/2″, 9/16″, 12,14,15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

Continue Reading Entry... »

The Audio2car is designed to provide endless hours of listening pleasure through most vehicles’ factory radios. To ensure that your Mobile Device performs correctly in your car or truck, we recommend that you read this entire manual before attempting installation of the Audio2car interface.

The Audio2car interface will allow you to connect your Mobile Device to a factory radio that has the ability to control a CD changer. The Audio2car is designed to be used with all iPods, mp3 players, portable DVD players, video game systems and any other portable device with traditional audio outputs.
(more…)

Continue Reading Entry... »

Turn the front wheels all the way to the left or right for mud guard installation. However, it may be necessary to remove the wheels depending on the tools being used for installation.
1. Clean and degrease the mud guard location area on the fender before installation.
2. Remove existing fastener from location D (Figure 1).
3. Attach mud guard to front fender with “existing factory fastener” at location D. Check fit and parallel and adjust accordingly before tightening (Figure 1).
4. Using mud guard as a template, mark, drill 1/8 holes and install #10 screws and washers at locations A, B, and C
(more…)

Continue Reading Entry... »

Selecting The Vehicle Type
Switches 1,2, and 3 are used to select vehicle type. Use the chart on the back of these instructions to determine which of the above switch settings you will need.
Window Roll Up Function
Turn Switch 4 on (up position) to enable the window roll up function or off (down position) to disable window roll up. Window roll up is not available for all vehicle types. Use the chart on the back of these instructions to determine which vehicles are compatible.
(more…)

Continue Reading Entry... »

The rack must be inspected before each use to make certain attachments are secure, and for evidence of Wear. Misuse of the rackor failure to observe the manufacit/rer ’s mär action s as to installation, proper Attachment and maintenance will void any warranties that may be implied by law.
1. Plastic Bag labeled #1 remove contents and press rubber protective strip #1 on to bottom of fairing #2.
2. Plastic Bag, labeled #2 re move c ontents and place black button head sere w #3 thru blac k washe r and then thru fairing #2. Place fairing onto bracket #4 and attach black washer, lock washer and wing nut finger tight only. Attach all 4brackets but do not attach fairing to rack at this time.
(more…)

Continue Reading Entry... »

Installation requires a professional mechanic. Prior to beginning, inspect the vehicles steering, driveline, and brake systems, paying close attention to the suspension link arms and bushings, anti-sway bars and bushings, tie rod ends, pitman arm, ball joints and wheel bearings. Also check the steering sector-to-frame and all suspension-to-frame attaching points for stress cracks. The overall vehicle must be in excellent working condition; repair or replace all worn parts. Read instructions several times before starting. Be sure you have all needed parts and know where they install. Read each step completely as you go.
(more…)

Continue Reading Entry... »