Automotive Manual PDF

The 1971-1974 Eldorado is a classic Cadillac that is fast becoming a collectable and appreciat
ing automobile. Sadly, even though Cadillac was a trend-setter in introducing wire wheels for their cars, the
current Eldorado owner has few choices when it comes to dressing their car up with wire wheels that add to
the elegance of the car. Roadster introduced a line of wire wheels that will work on these cars, however, due to
the very limited room in the rear wheel wells and close proximity of the fender skirt fastening hardware, the wire
wheels require that there be a few changes made to accomodate the wheels. It is our opinion that these
changes should be performed by a qualified bodyshop or fabricator so that there is no risk of harming
your car. The purpose of these instructions are to demonstrate what modifications will be involved. None of
these modifications will spoil or detract from the original appearance of your car. The modifications required are
all to areas that cannot be viewed from the outside.
(more…)

[Read more →]

STEP 1. In front of shifter knob locate and remove a small clip that holds the shifter knob in place. Using your hook tool to get behind the small clip and pull outward. Set clip aside. Grasp the shifter knob and pull up to remove. Insert the hook tool underneath the right rear corner of the bezel that surrounds the shifter. Pull upward to release one (1) clip. Perform the same action in the remaining three corners of the bezel. Set the the parking brake and shift the transmission into neutral. Pull the ashtray insert out and set aside. Locate a 9/32” hex head screw behind where the ashtray insert was. Remove that screw with your 9/32” socket and ratchet. Set the screw aside. Grasp the bezel that surrounds the shifter knob and pull it up and over the shifter handle. Disconnect all wiring and set bezel aside.
(more…)

[Read more →]

The Autronic-Eye is an electronic device that automatically switches the headlamps between the upper and lower beams on the car to which it is installed, in response to light from an approaching car. It consists of four individual units: Phototube Unit, Amplifier Unit, Power Relay, and Auxiliary Foot Switch.
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.

SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.

SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, and jack stands
(more…)

[Read more →]

Parts Needed For This Radio Install Parts REQUIRED for the install Description Dash installation kit Multi purpose General Motors Snap on in dash wire harness General Motors 1978 - 1988 You will need one antenna extension cable. Typical lengths: 6”, 1 ft, 3 ft 4 small washers
(more…)

[Read more →]

This booklet contains important information about the warranty coverage of the General Motors warranties covering your new Cadillac. Keep it with your vehicle and make it available to a Cadillac dealership if warranty work is needed. The booklet should remain with your vehicle when you sell it so future owners will have the information.
(more…)

[Read more →]

Please take a few moments to review this manual thoroughly before you begin work: Μake quick parts check to make certain your kit is complete (see shipper parts list in this package). If you discover shipping damage or shortage, please call our office immediately. Take a look at exactly what you are going to need in terms of tools, time, and experience.
(more…)

[Read more →]

Thank you for choosing the Superchips Model 2724 MAX MicroTuner, a state-of-the-art instrument that allows you to install a Superchips performance program specifically tuned for your GM vehicle and your driving requirements.

You can custom tune your shift points and shift firmness, and optionally raise the vehicle rpm and speed limiters. Vehicles with electronic speedometers allow for correction to compensate for gear changes. The Model 2724 MAX MicroTuner also allows you to adjust the turn-on temperature for your vehicle’s electric fans. This product is intended for use on unmodified stock engines and stock transmissions. It can be used on vehicles with aftermarket air filters and cat-back exhaust.
(more…)

[Read more →]

Please take a few moments to review this manual thoroughly before you begin work: Μake quick parts check to make certain your kit is complete (see shipper parts list in this package). If you discover shipping damage or shortage, please call our office immediately. Take a look at exactly what you are going to need in terms of tools, time, and experience. Review our limited warranty with care.
(more…)

[Read more →]