Automotive Manual PDF

When we say complete, we mean COMPLETE. All kits come with a solid mass flywheel, disc, pressure plate assembly, alignment tool, pilot bearing already pressed in the flywheel, release bearing, as well as all new flywheel bolts, washers(where applicable) and clutch mounting bolts.
(more…)

[Read more →]

These instructions will cover the EMS Offroad Hub conversion kits:
• 94-99 Dodge 2500/3500 (HC-94D-xx)
• 00+ Dodge 2500/3500 (HC-00D-SRW-xx)(HC-00D-DRW-xx)
• 98+ Ford Super Duty (HC-SD-xx)
DRW = Dual Rear Wheel
SRW = Single Rear Wheel
1. Read all instructions before starting. Do not attempt the install unless you are an equipped and experienced mechanic.
2. When working with tools and chemicals, always wear the required safety equipment and glasses.
(more…)

[Read more →]

This VIZORLIGHT‐S®:
• Is designed for use with 2006 through the current Dodge Charger/Magnum model.
• Is designed and intended to function as an emergency warning light mounted to the windshield visors.
• Has an electric operating system requirement of 12 volts DC, with a negative ground.
• Will operate independently or in conjunction with Rontan light controllers or universal light controllers (ICM30® or ICM40® required).
(more…)

[Read more →]

The ATS Co-Pilot module commands the lock-up clutch of the torque converter along with the exhaust brake, if equipped, to stay engaged. This allows for up to 100% of the retarding force to be transferred in 3rd and 4th gear and the transmission oil temperature to remain low because of little to no slippage occurring when the converter is in these selected gears. When the ATS Valve Body is installed, you can use engine braking in the low-speed position of nearly 12 mph in 1st or 2nd gear.
(more…)

[Read more →]

The AD38 is a small standalone device that can overwrite the pin code stored within the skim module fitted to Chrysler/Jeep & Dodge vehicles fitted with CAN 2,3,4,5 and 6 systems. This will then allow new keys to be programmed into the vehicle. The skim module is Chrysler terminology for a combined immobiliser and aerial module. Writing a new pin code to the skim module involves removing the Skim module, which is located around the ignition barrel, from the vehicle, which is a fairly simple process.
(more…)

[Read more →]

Dodge Charger Figure Grille Installation
Figure 1. Examples of low-profile Philips screwdrivers. 1) Ratchet (¼” drive) with ¼” socket and Philips bit. 2) Offset Philips screwdriver.
1.1) Remove radiator covers. Begin by popping the hood of your vehicle. There are two plastic protective shields which cover the radiator area. These are held in place by small clips which will let go easily by pulling on the pieces. Fig. 2 shows these covers and illustrates their removal.
(more…)

[Read more →]

AMP RESEARCH BEDSTEP™ – DODGE RAM
Locate rear bumper attachment point on driver side. Remove bumper fasteners. Install upper mount onto linkage as shown and torque bolts to 33 ft-lbs / 44 Nm. Slide upper mount over factory studs, install fasteners and torque to 59 ft-lbs / 80 Nm. Install step pad assembly onto linkage assembly with two socket cap screws. Adjust step pad position side to side. Allow for foot access. Torque allen head bolts to 10 ft-lbs / 13.5 Nm.
(more…)

[Read more →]

Measure from the center of the wheel up to the bottom edge of the wheel opening
LF______ RF______ LR______ RR______2.
NOTE: The factory service manual specifically states that striking the knuckle to loosen the ball joints or tie rod ends is prohibited. Striking the aluminum knuckle can damage it. A special puller tool #8677 (or equivalent ball joint tool) is recommended to be used to separate these components from the knuckle.
(more…)

[Read more →]

1. Remove the negative battery cable first, then the positive battery cable. If equipped, the Supplemental Restraint System will be deactivated when the battery is disconnected.
2. Measure and record the space between the bumpers and the body as well as the space between the cab and bed for reference during installation of this kit.
(more…)

[Read more →]

Congratulations! You have purchased the finest street Supercharger available for the 1997/2001 5.2/5.9L Dodge engine. The centerpiece of this kit is the highly efficient and reliable Paxton Automotive Corp. NOVI 2000 supercharger. A mechanically driven (by belt) centrifugal blower (supercharger). This kit comes with all of the parts you’ll need for a successful installation. The operations required have been grouped in order of sequence.
(more…)

[Read more →]