Automotive Manual PDF

TO START:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Loosen and remove the air cleaner wing nuts, then remove the air cleaner lid.
3. Disconnect the cold inlet tube and then remove the air cleaner base assebmly as shown.
NOTE: Some vehicles are equipped with and air injection check valve which is vented to the air cleaner assembly. On these vehicles, remove the rubber hose and clamp the provided filter to the check valve.
4. Loosen and remove the two bolts that secure the air inlet/resonator, then remove the assembly as shown.
NOTE: K&N recommends that you do not discard your factory air intake.
(more…)

[Read more →]

Step Description
1. Place the vehicle on a hoist that leaves the entire underside of the frame.
2. Drain all the fuel from the original equipment tank using a pump or siphon. In some cases Dodge tanks have a screen at the tank inlet which won’t allow a siphon hose to enter. In this case, it may be necessary to drive the vehicle until fuel is as low as possible in the tank.
3. Disconnect 1 ½” fuel tank full hose and ¾” vent line hose from fill spout, leaving them attached to the tank.
4. Disconnect electrical connection, feed line and return line from the sending unit. Press in the tabs on the connection fittings to release fuel lines.
(more…)

[Read more →]

Congratulations on purchasing the FM Fuel Rail! We’re confident that this is a high quality piece that will help ensure the safety and performance of the engine in your Miata. Following are instructions that will help you safely install this piece.

1. The fuel system first needs to have its pressure re- lieved. There are two ways to do this, it’s safest to do them both. First, find the relay that’s pictured to the side. It will be underneath the dash, near the steering column. It should look similar to the relay in the picture, but different years had different relays, so it might not be exactly the same. Look for a blue wire with a red stripe, that’s the wire that goes to the fuel pump. Start the car and let it idle. While the car is idling, unplug the relay. This will kill the engine, as it’s no longer being fed the fuel it needs. Turn the car off once the engine has stopped. The gas cap also needs to be removed, to ensure that pressure doesn’t build up in the tank. Don’t reinstall it until the fuel rail is in.
(more…)

[Read more →]

The installation of the FASS FUEL SYSTEM can be relatively simple when the following steps are followed.
1. Inventory the package components completely. Notify place of purchase immediately of any parts missing or damaged.
2. We have invested many hours into the development of the installation and owner’s manual’s to simplify the installation and operation of the FASS Fuel System. Please read the owner’s manual and the installation manual completely before attempting installation. Understand how the system operates and installation recommendations before beginning installation. Most of the questions that you will have will be answered in one of these manuals. If you have a question please review the installation or owner’s manual.
(more…)

[Read more →]

Step 1- Determine the Correct Fuel Line Adapter
This section aids in determining the best fuel line adapter in your kit to use to maintain fuel supply for the E3 Fuel Saver 7000.
IMPORTANT
If you have Electronic Fuel Injection (EFI) system with a high pressure fuel line with a “Schrader valve fuel stem” proceed to the section entitled “INSTALLING THE SCHRADER VALVE CONNECTORS” shown on the next page. If you have a Schrader Valve Stem, you will need the correct Schrader adapter (either FORD or UNIVERSAL Schrader adapter). These adapters are included in your kit. If your engine is NOT EQUIPPED with a high pressure fuel rail Schrader valve stem, then proceed to the section “INSTALLING THE GASOLINE SUPPLY MODULE.”
(more…)

[Read more →]

Do not perform this install near a flame source due to the risk of fire or explosion from gas fumes. Use a jack to lift rear of vehicle. Remove the passenger side rear tire. Remove the wheel well cover to expose the fuel filler neck behind the quarterpanel.
Note: For manual locking or manual non-locking fuel doors, do steps 1-4 only. For electric locking fuel doors, do all steps.
(more…)

[Read more →]

The MotorVac CarbonClean System is a self-contained cleaning system, designed to connect to any gasoline engine. Once the unit is connected, it temporarily replaces the regular fuel supply with a mixture of gasoline and the specially formulated MotorVac CarbonClean Detergent and Top Engine Cleaner.
(more…)

[Read more →]

Fuelpak maps for the LTR450 were created with a White Brothers Power Pro performance module installed. The included Power Pro unit must be used in conjunction with the Fuelpak for proper function. Failure to do so will result in poor performance and may cause engine damage.
(more…)

[Read more →]

If you have a high mileage vehicle, we recommend changing the fuel filters inside the module. The primary fuel filter and the inlet filter sock are not currently available as service parts from GM so changing these filters requires purchasing an all new fuel pump module. Complete fuel pump modules are available from LPE (see part number listed above).

Installation Instructions:
1) Follow the GM service instructions for removing the fuel pump module from your vehicle. Service manuals are available from Helm Inc. ( http://www.helminc.com ).
2) Unplug all the wires from the bulkhead connector at the top of the module.
3) Carefully remove the outer “bucket” from the fuel pump module assembly.
4) Using a small pocket screwdriver, carefully pry the fuel sock (fuel pump inlet filter) from the center pin on the bottom of the fuel pump. Save the fuel sock. You will be reusing the fuel sock when you reassemble the module.
5) Using wire cutters, clip the small ground wire as close to the fuel pump terminal as possible.

Get pdf LS2 equipped SSR & Trailblazer SS High Fuel Pump Upgrade Kit Installation Instructions

[Read more →]

ON–VEHICLE INSPECTION
1. CHECK FUEL PUMP OPERATION
(a) Using SST, connect terminals +B and FP of the data link connector 1.
(b) Turn the ignition switch ON.
NOTICE: Do not start the engine.
(c) Check that there is pressure in the hose from the fuel filter.
(more…)

[Read more →]