Automotive Manual PDF

RSS Feed

The Resources for Automotive

Entries Tagged as 'GMC'

2001–2003 GMC Duramax 6.6 Fitch Part # F758186BD Installation Instructions

October 19th, 2009 · No Comments

Do not smoke or be near open flame while performing installation. Wear eye protection as the fuel system is under pressure.
Kit includes
• Installation bracket, fuel line disconnect tool, and cable/zip ties.
• EFI multi port fuel injection hose and fuel line quick connect fittings.

Installation Procedure
• Screw the 90* fittings into the top and bottom of the Fitch unit. Tighten down the lock nut on the 90* fittings.
• Using the 18” hose with the female plastic fitting, screw the opposite end to the 90* fitting at the top of the Fitch unit and the 6” male hose to the bottom of the Fitch unit.
(more…)

[Read more →]

99-02 Chevy/GMC K1500 4×4 6″ Suspension lift Installation Instructions

October 18th, 2009 · No Comments

FRONT DISASSEMBLY:
1. With vehicle on flat level ground set the emergency brake and block the rear tires. Place floor jack under the lower control arm’s front cross member and raise vehicle. Place jack stands under frame rails, behind the front wheel wells then and lower the frame onto the stands.
2. Remove both front factory skid plates located in front of and under the front differential using 15mm socket.
WARNING: Be extremely careful when loading or unloading the torsion bars; there is a tremendous amount of stored energy (load pressure) in the bars. Keep your hands and body clear of the adjuster arm assembly and puller tool in case anything slips or breaks.
(more…)

[Read more →]

Chevrolet Silverado/GMC Sierra Rear Vision System – NAV Display Installation Instructions

October 18th, 2009 · No Comments

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety. Install Camera into Endgate
(more…)

[Read more →]

2006 Chevy Silverado 2500/3500 Exhaust System Installation

October 17th, 2009 · No Comments

These Borla Performance Cat-Back™ Exhaust Systems have been designed for 2006 Chevy Silverado 2500/3500 and 2006 GMC Sierra 2500/3500 each equipped with 6.6L Diesel V8 engine, 2 or 4-wheel drive and automatic or manual transmissions. 140180 is designed for Crew Cab Long Bed; 140181 is designed for Crew Cab Short Bed; 140182 is designed for Extended Cab Long Bed; 140183 is designed for Extended Cab Short Bed.
(more…)

[Read more →]

2007-08 Chevy/GMC Ton, Crew Cab, 2/4wd 3″ Body Lift Installation Instructions

October 17th, 2009 · No Comments

Zone Offroad Products recommends this system be installed by a professional technician. In addition to these instructions, profes-
sional knowledge of disassembly/ reassembly procedures and post installation checks must be known. Minimum tool requirements
include the following: Assorted metric and standard wrenches, hammer, hydraulic floor jack and a set of jack stands. See the “Special
Tools Required” section for additional tools needed to complete this installation properly and safely.
(more…)

[Read more →]

99-up Chevy/GMC Truck Tailgate Cap Instructions

October 16th, 2009 · No Comments

1. Remove the factory plastic tailgate cap.
A. Remove any tape residue from the truck by wrapping a cloth shop towel or terry cloth rag tightly around knuckles and push firmly against remaining tape.
B. Remove any remaining glue or dirt with Naptha, Paint Thinner or Adhesive Remover. Then clean surface with Isopropyl alcohol and wipe clean.
C. If you have purchased the gray smooth paintable Tailgate Cap go to step 2; if you have purchased the black textured Tailgate Cap go to step 3.
(more…)

[Read more →]

2001-2004 Chev/GMC Duramax Diesel “Cool Duals” Installation Instructions

October 14th, 2009 · No Comments

Removal of stock system:
First using 15mm socket or wrench, remove four (4) nuts at flange located approximately under the passenger side seat. Remove rear exhaust from rubber hangers and remove the system from under the truck.
NOTE: If you have purchased the optional front pipe, Remove the stock front pipe on the truck by removing the exhaust hanger on the transmission using a 13mm socket, then remove the band clamp at the front of the pipe, then remove stock front pipe from the truck. ( Note: the band clamp will be re-used during the installation of your new MBRP system)
(more…)

[Read more →]

99-07 Chevy & GMC Full Size Part # 000937, 000938 Installation Instructions

October 13th, 2009 · No Comments

REMOVAL:
1. Engage the steering column / ignition switch lock with the steering wheel & wheels centered. (NOTE It may be necessary to remove the upper and lower steering shaft bolts prior to locking for accessibility)
2. Remove the two bolts holding the upper shaft in place. One is located in the engine compartment; the second is located under the dash at the base of the steering column.
3. Compress factory shaft assembly and remove it from under the dash. Do not spin wheel with shaft removed.
(more…)

[Read more →]

01-06 Chev/GMC 6.6L Duramax Diesel Extended Cab Short & Long Bed Installation Instructions

October 13th, 2009 · No Comments

Removal of stock system:
1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators.
2. Using a 15mm socket or wrench, disconnect the factory exhaust system at the four bolt flange located behind the catalytic converter. If the vehicle is not equipped with a catalytic converter disconnect the four bolt flange located approximately under the passenger side seat.
3. Remove the exhaust system from the rubber insulators and remove from under the vehicle. If a hoist is not available for use, it may be necessary to cut the tail pipe behind the muffler for removal of the system.
4. Unbolt the OEM hanger from the transmission and remove.
5. Loosen the factory band clamp and remove the stock front pipe. Some vehicles are not equipped with a catalytic converter. Do not discard the band clamp as it is required for the installation.
6. Remove the spare tire. You may not be able to reinstall your spare tire after the installation of this exhaust system.
(more…)

[Read more →]

2007-2008 Chevrolet & GMC Truck with a 5.3L, 6.0L & 6.2L V8 Mac Performance Instructions

October 12th, 2009 · No Comments

1. Start by disconnecting the wire harness from the MAF sensor as shown.
2. Remove the cover from the intake manifold by lifting it up and then pulling it out as shown.
3. Unplug the vent air tube from the stock air silencer as shown.
4. Remove the clip holding the radiator hose to the stock air tube as shown.
5. Loosen the hose clamp on the stock air tube at the MAF meter and the throttle body and remove the stock air tube as shown.
6. Remove the cover of the stock air box as shown and set aside.
(more…)

[Read more →]