Automotive Manual PDF

RSS Feed

The Resources for Automotive

Search Results for 4 6 3 valve camshaft position sensor

Petrol Engine Twin Camshaft Setting/Locking Tool Set

August 19th, 2009 · No Comments

Setting engine timing on all current Ford 16v, Twin Camshaft engines (Zetec/Duratec) requires the tools included in VS1152.V2 Set.
Additionally, replacement of the timing belt requires the crankshaft pulley to be removed and therefore Associated Tools VS1013 or VS4736 are needed, depending upon engine type.
CAMSHAFT SETTING PLATE – VS115/01

[Read more →]

Tags: Misc

Suzuki Hayabusa Gear position indicator Geartronics GPI-4 Fitting instructions

October 2nd, 2008 · No Comments

The gear indicator comes configured for use with the OEM Suzuki gear position sensor, and is fitted with standard connectors to plug directly into the Suzuki wiring harness. The unit also features the so-called ‘TRE’ modification, which is designed to defeat the gear dependent mapping strategy of the Suzuki ECU. Please refer to the bottom [...]

[Read more →]

Tags: Suzuki

1996-1999 VW/ Audi 1.8L AEB Engines Revised Camshaft Sprocket Bolt Torque

December 8th, 2008 · No Comments

Previously published service information regarding camshaft sprocket bolt torque specifications for the 1.8L Volkswagen/ Audi 1.8L AEB engines may have incorrectly listed the torque value at 74 ft.lbs.
The correct torque value for the camshaft sprocket bolt is 48 ft.lbs. (65 Nm).These cylinder heads are beginning to be seen in machine shops because many miles have [...]

[Read more →]

Tags: Audi · Engine · Volkswagen

Ford 4.6L/5.4L 3 Valve engine cam phasers

July 8th, 2009 · No Comments

Ford’s cam phasers are specially designed, computer-controlled cam gears that have the ability to adjust camshaft position (centerline – advance or retard) while the engine is running. They are used on all 2005 and newer, Ford 3 Valve Modular engines. Since the Modular 3V engine uses two camshafts, one phaser is required for each camshaft [...]

[Read more →]

Tags: Ford

Tire Temperature Sensor Installation Guide Manual

March 25th, 2008 · No Comments

Tire Temperature Sensor Installation Introduction Technical Support Parts Installation Assembling the Sensor Wiring the Sensor Securing the Mounting Bracket and Sensor Assembly INTRODUCTION The tire temperature sensor allows you to monitor the temperature of the motorcycle tire. TECHNICAL SUPPORT For assistance, please contact Dynojet Technical Support at 1-800-992-3525, or write to Dynojet Research at [...]

[Read more →]

Tags: Misc

Geartronics GPI-4 Suzuki Hayabusa Gear position indicator Fitting instructions

September 29th, 2008 · No Comments

The gear indicator comes configured for use with the OEM Suzuki gear position sensor, and is fitted with standard connectors to plug directly into the Suzuki wiring harness. The unit also features the so-called ‘TRE’ modification, which is designed to defeat the gear dependent mapping strategy of the Suzuki ECU. Please refer to the bottom [...]

[Read more →]

Tags: Suzuki

Oxygen Sensor – Low Voltage?

December 22nd, 2010 · No Comments

I ran numerous Diagnostics tests with the OBD-II readers and replaced many oxygen sensors (Bosch and Delphi) with my 2000 Chevrolet Silverado. But my check engine light has been on for the past month with the new oxygen sensor. The last test, I replaced the Bosch oxygen sensor with a Delphi. I made a quick [...]

[Read more →]

Tags: Misc

How to get the O2 sensor repaired?

December 29th, 2010 · No Comments

i have a 99 cadillac escalade and the o2 sensor is failing and i was wondering how to go about getting that fixed and will that stop my car from passing a texas state inspection?
- New one is right. There may be two or three of them though. You’ll have to get the right one [...]

[Read more →]

Tags: cadillac

Why won’t my ford engine run with map sensor hooked up?

December 16th, 2010 · No Comments

we took the engine out of a 87 crown victoria and put it in the ford f150. we used the intake from the f150 and the rest of the engine from the crown vic. why won’t it run with the map sensor hooked up now?

[Read more →]

Tags: Ford

R8907 Sensor Kit For 5.7 Liter GMC Diesel Engine Using R8503 Tachometer Installation Instructions

October 20th, 2009 · No Comments

1) Scrape away the paint from two areas directly across from each other near the front of the vibration damper as shown on the back page. Roughen the bare metal with an emery cloth. Clean the magnets and bare metal on damper with alcohol to remove any oil or grease residue so that the glue [...]

[Read more →]

Tags: GMC