Automotive Manual PDF

Certain Zone Suspension Products are intended to improve off-road performance. Modifying your vehicle for off-road use may result in the vehicle handling differently than a factory equipped vehicle. Extreme care must be used to prevent loss of control or vehicle rollover. Failure to drive your modified vehicle safely may result in serious injury or death. […]

[Read more →]

Performer series intake manifolds are compatible with aftermarket camshafts and headers designed to operate in the idle-5500 RPM range. Edelbrock offers a dyno-matched, street proven camshaft; Performer-Plus #2172. Header primary tube diameter should be 1-5/8” depending on your specific engine combination.

[Read more →]

Edelbrock Performer series intake manifolds are designed for engines operating in the idle to 5500 rpm range. Performer RPM series intake manifolds are designed for engines operating in the 1500-6500 rpm range. Match Performer or Performer RPM intake manifolds with recommended carburetors and additional equipment for even greater performance increases.
EGR SYSTEMS: Edelbrock EGR-equipped Performer manifolds […]

[Read more →]

Adapter plate F-15741-TL29PL is required to hold VW 09G (TF-60SN) and Volvo/Opal (TF-80SC) valve body sections while reaming. Adapter plate is not required for Ford/Mazda (TF-81SC).
Note: Mounting instructions are included with the Adapter plate F-15741-TL29PL. Disassembly Steps
Remove the retainer, plunger sleeve with plunger valve, spring and lock-up valve. Keep the retainer for re-use and discard […]

[Read more →]

Pre-Installation Notes
1. Special literature required: OE Service Manual for model/year of vehicle. Refer to manual for proper disassembly/reassembly procedures of OE and related components.
2. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the OE manual.
3. Larger rim and tire combinations may increase leverage on suspension, steering, and related components. When […]

[Read more →]

Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Loosen clamp at intake manifold leaving clamp on hose.
3. Slide hose tube assembly back and insert power plate into hose.
4. Reinstall tube hose assembly making sure power plate is engaged in tube while locating and tightening hose clamp.

[Read more →]

The RetroGauge™ Mini-Tach is designed for use with a standard ignition coil as factory fitted to 1967 and 1968 Ford Mustangs. For aftermarket ignition systems please read the important application note at the bottom of the page.
INSTALLATION
1. Disconnect the battery negative terminal from the vehicle to completely isolate the electrical system.
2. Remove the instrument cluster […]

[Read more →]

ReadyLift Suspension Inc. recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks must be known.
PRODUCT SAFETY WARNING: Modifying your vehicle ride height may result in the vehicle handling differently than a factory equipped vehicle. Extreme care must be used to […]

[Read more →]

KIT FITS: 1950 - 1964 ½ and ¾ ton Ford pickups and panels F-1, F-100, F-150. These instructions covers Drop Axle Kit as well but steering link and both tie rods are different. KIT INCLUDES: Plates for each side of frame rail with tubes pre-welded and pre-drilled for steering box mounting, seamless heavy wall tubing […]

[Read more →]

Hardware kit sold separately, contact your local dealer/distributor for further information.
Removal of stock system:
Remove nut, with 15mm wrench or socket, from band clamp in front of muffler.
Remove rear exhaust from rubber hangers, remove bottom shock bolt at rear of truck &
separate the stock exhaust at the slip joint at the muffler.
Remove the muffler and tail […]

[Read more →]