Automotive Manual PDF

RSS Feed

The Resources for Automotive

Search Results for Passlock for 2000 Chevy Silverado

VATS / PASSLOCK / TRANSPONDER Universal Alarm Bypass Module

December 5th, 2008 · No Comments

This module lets you bypass virtually any type of vehicle factory anti-theft system on the market today to remotely start your vehicle without permanently disabling the vehicle factory theft system.
In 1985, General Motors came out with their first Vehicle Anti Theft System known as VATS which uses a resistor pellet in the key. Since this [...]

[Read more →]

Tags: Misc

GMC Sierra/ Chevy Silverado, GMC/Chevy HD Cut Out Flare Installation Instructions

August 30th, 2009 · No Comments

NOTE: Bushwacker only approves installing the flares according to these written instructions with the hardware provided.
WARNING: Failure to install according to these instructions will invalidate the warranty. This includes, but is not limited to using alternative installation methods, hardware, or materials. DO NOT USE: Loctite, SuperGlue, or similar products on the hardware or the flares.

[Read more →]

Tags: GMC

2006 Chevy Silverado 2500/3500 Exhaust System Installation

October 17th, 2009 · No Comments

These Borla Performance Cat-Back™ Exhaust Systems have been designed for 2006 Chevy Silverado 2500/3500 and 2006 GMC Sierra 2500/3500 each equipped with 6.6L Diesel V8 engine, 2 or 4-wheel drive and automatic or manual transmissions. 140180 is designed for Crew Cab Long Bed; 140181 is designed for Crew Cab Short Bed; 140182 is designed for [...]

[Read more →]

Tags: GMC

1988-1998 Chevy Silverado & GMC Sierra Hog Bar Installation Instructions

August 29th, 2009 · No Comments

Pre-installation Preparation
1. Verify kit contents.
2. Remove protective wrapping from hog bar
and place on a non-abrasive surface.
3. Remove the brackets and hardware from
the box.
B. Remove Tow Hooks
1. Locate the Bolts that hold the tow hooks in
place we will be using these bolts for the
brackets.
2. Remove the bolts that hold the tow hooks
in place by using an [...]

[Read more →]

Tags: GMC

Chevy/GMC Silverado/Sierra P/U 1500 4 Door Pro Step Installation Instructions

September 13th, 2009 · No Comments

Before Starting Installation
1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified.
4. Special tools needed:
a. 17/64” & 5/16” drill bits
b. Tool to trim [...]

[Read more →]

Tags: GMC

2007-2008 Chevy 4.8, 5.3, 6.0 Silverado/Sierra VPI Cold Air Performance Intake System Installation

October 4th, 2009 · No Comments

Installation Instructions:
1. Disconnect negative battery cable. Then loosen all three factory hose clamps located at the Mass Air Flow (MAF) meter and both factory intake tube.
2. Remove black cover on throttle body by pulling up and sliding towards front of truck. It is held by two grommets. Gently pry the radiator hose bracket from the [...]

[Read more →]

Tags: Chevrolet

1999-2000 Chevrolet/GMC Silverado/Sierra 3/4 Ton 3″ Body Lift Kit

July 16th, 2008 · No Comments

1. Remove negative battery cable, then positive battery cable from the battery. If equipped, the Supplemental Restraint System will be deactivated when the battery is disconnected.
SteeRIng extenSIon
2. Remove the nut and bolt holding the steering column to the steering shaft located in the engine compartment about 8 inches down from the firewall. Mark the two [...]

[Read more →]

Tags: Chevrolet

99-06 Chevy/GMC Silverado/Sierra 6.5 Bed GM-001 Armor Lid Installation Manual

September 29th, 2009 · No Comments

This truck bed cover is designed for trucks that DO NOT have a bed liner. Trucks that DO have a bed liner may require some minor trimming or modification of the bed liner to insure proper placement for the brackets. Trimming or modification will vary between different brands of bed liners and model of your [...]

[Read more →]

Tags: GMC

2004-2005 Chevy Silverado 2500HD & 3500 Brute Force Intake System Installation

September 19th, 2009 · No Comments

The AEM Brute Force Intake System is the result of extensive development on a wide variety of cars. It is the most advanced short pipe air intake system on the market. Each system is specifically engineered for its particular application. All AEM Brute Force Intake Systems deliver maximum performance gains through the lightweight, all-aluminum, mandrel-bent [...]

[Read more →]

Tags: Chevrolet

1999-2005 Chevy 1/2-TON Silverado / GMC Sierra 4WD Superlift Rail Wrap Installation

September 4th, 2009 · No Comments

Installation requires a professional mechanic. Prior to beginning, inspect the vehicles steering, driveline, and brake systems, paying close attention to the suspension link arms and bushings, anti-sway bars and bushings, tie rod ends, pitman arm, ball joints and wheel bearings. Also check the steering sector-to-frame and all suspension-to-frame attaching points for stress cracks. The overall [...]

[Read more →]

Tags: GMC