Automotive Manual PDF

RSS Feed

The Resources for Automotive

Ford Contour QuickLIFT Installation Guide

August 4th, 2010 · No Comments

Step 1 – Unpack QuickLIFT kit and verify contents. Remove all items from the packing tube. You should have the following before beginning: * [Group 1 - Fender] (2) shorter fender Ball-studs & (4) washers with (2) nuts. * [Group 2 - Hood] (2) Ball-studs with 12 mm fitting & (2) washers. * [Group 3 - Gas Springs] (4) Locking clips * (2) QuickLIFT Gas Springs * Printed Instructions
Step 2 – Gather required tools. Please gather the following tools before you begin the installation: * Power Drill * 5/16 drill bit. * 1/2″ open ended wrench. * 1/2″ deep well socket. * 12 mm open ended wrench or socket wrench. * 10 mm open ended wrench or socket wrench. * Fine permanent marker * Center punch & hammer – optional.
(more…)

[Read more →]

2003-2006 Hummer H2 6.0L V8 Part #3060 Installation Instructions

January 27th, 2010 · No Comments

1. Start by unplugging the MAF sensor by using a screw driver to remove the clip as shown.
2. Push fitting in and pull up to remove the wire harness from the MAF sensor.
3. Remove the bolts that hold the stock air box in place as shown and set aside for reuse with the MAC system.
4. Unbolt the engine cover by using a 10mm socket as shown and set the hardware aside for reuse.
5. Remove the cover to gain access to the hose clamp at the throttle body as shown.
6. Loosen the hose clamp on the stock air tube that attaches at the throttle body as shown.
(more…)

[Read more →]

93-97 Honda Accord SOHC, DOHC, VTEC, Non-VTEC, 2.2L PowerAir Throttle Body Spacer

November 18th, 2009 · No Comments

1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Disconnect electrical connectors to throttle body & factory intake tube. See Fig#1
3. Using a 10mm socket, remove two bolts holding throttle cable bracket to intake manifold. Retain bolts for later use. See Fig#2
4. Remove throttle cable(s) from throttle body.
5. Using a Phillips screwdriver, loosen hose clamp on factory intake tube & remove tube from throttle body & air box. See Fig#3
(more…)

[Read more →]

08-09 Honda CRV Steelcraft 3″ Sidebars Installation Instructions

November 14th, 2009 · No Comments

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Determine driver and passenger Mounting Brackets.
3. Hang the inner side of the driver front Mounting Bracket into position by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame (Figure 1). NOTE: There are two threaded holes by the front mounting location on the frame, use the one towards the rear of vehicle.
4. Attach the opposite side of the driver front Mounting Bracket to the threaded holes on the floor panel of the vehicle by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers (Figure 1).
5. Locate and cut out the openings in the driver and passenger side trimming templates with a pair of scissors (Page 3 & 4)
6. Fit the driver’s side template onto its respective side plastic rock shields. Position them using two each of the 8mm bolts that will later be used to mount the side bar brackets. Transfer the openings in the templates onto the plastic cover using a magic marker.
7. Now remove the rock shield from the undercarriage of the car. The three front screws can be removed with a 10MM socket. The plastic retainer plugs can be removed with a flat blade screwdriver.
8. Using a sharp knife or pair of shears, cut out the shields as marked using the templates (Figure 2).
9. Insert the inner side of driver rear Mounting Bracket through previously cut out hole on the plastic cover. Hang Mounting Bracket by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame (Figure 3). NOTE: There are two threaded holes on the frame, use the one towards the rear of vehicle.
10. Attach the opposite side on the driver rear Mounting Bracket by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers into factory threaded holes on the floor panel.
11. Position Driver Side Bar onto Mounting Brackets. Attach Side Bar to Mounting Brackets using the included (4) 8mm x 30mm Hex Head Bolts, (4) 8mm Lock Washers, and (4) 8mm Flat Washers (Figure 1). Do not tighten at this time.
12. Level and adjust Side Bar; then tighten all hardware at this time.
13. Re-install the rest of fastener on the rock shield.
14. Repeat steps 2-13 for passenger Side Bar.
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Get pdf

[Read more →]

HONDA TRX450R Frame Skid Plate Installation Instructions

November 8th, 2009 · No Comments

Preparation:
a) Lock rear parking brake on quad, turn gas petcock to Off and stand quad upright on the rear grab bar. Make sure vehicle is secure and will not fall over while installing your new skid plate.
b) Remove OEM bolts mounting the OEM Frame Cover to the Frame using a 10mm socket wrench. You may discard the OEM mounting bolts and plastic frame cover.
(more…)

[Read more →]

1988-2000 Honda Civic & Acura 1.6 EL TWM Performance Short Throw Shifter Installation Manual

October 28th, 2009 · No Comments

1. Unscrew the stock shift knob by rotating it counter clockwise.
2. Remove all screws securing center console and remove console.
3. Remove the rubber dust boot surrounding the shifter, use caution not to damage it. Put it in a safe place for re-installation later.
4. Place the car up on a lift, or use a jack and jack stands to raise it off the ground. Loosen the nut on the base of the shifter using a 12mm socket and ratchet. You may need to hold the head of the bolt on the opposite side of the shift rod with a wrench to loosen the nut.
(more…)

[Read more →]

2004 Chevy HD Truck Duramax Diesel High Output “LLY” Installation Instructions

October 12th, 2009 · No Comments

Tools Required For Installation:
Flat Head Screwdriver
8mm, 10mm Socket
Ratchet & Extension
3/32”, 5/32” Allen Wrench
#T20 Security bit (Included)
1. Disconnect the negative battery cable. Disconnect the Mass Air Flow (MAF) sensor wiring harness. Using the supplied T-20 Security bit, remove the two screws and the Mass Air Flow sensor from the tube (save the sensor for reuse). Loosen the hose clamps on each end of the factory intake tube assembly.
(more…)

[Read more →]

2007-2008 Chevrolet & GMC Truck with a 5.3L, 6.0L & 6.2L V8 Mac Performance Instructions

October 12th, 2009 · No Comments

1. Start by disconnecting the wire harness from the MAF sensor as shown.
2. Remove the cover from the intake manifold by lifting it up and then pulling it out as shown.
3. Unplug the vent air tube from the stock air silencer as shown.
4. Remove the clip holding the radiator hose to the stock air tube as shown.
5. Loosen the hose clamp on the stock air tube at the MAF meter and the throttle body and remove the stock air tube as shown.
6. Remove the cover of the stock air box as shown and set aside.
(more…)

[Read more →]

2007-09 Chevrolet/GMC HD Pickup GMT-900 Platform “LMM” 6.6L Duramax Diesel Instructions

September 27th, 2009 · No Comments

Installation Step:
1. Disconnect the negative battery cable. Using a 5/16” socket or flat screwdriver, loosen the hose clamp that holds the factory airbox to the flexible intake tube.
2. Using a #20 Torx bit, remove 2 screws holding the Mass Air Flow sensor to the factory airbox tube. Remove the MAF and set it aside. Remove the factory filter minder and grommet from the factory airbox. Save them for later use in step #10.
3. Slide the flexible intake tube off of the factory airbox and then rock the airbox back and forth to free it from the mounting grommets, next lift it straight up and remove it from the vehicle.
(more…)

[Read more →]

03-04 Chevy Duramax / 01-04 GMC Duramax 6.6L Installation Instructions

August 29th, 2009 · No Comments

Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned using the Airaid Filter Tune-Up Kit periodically.
(more…)

[Read more →]