Automotive Manual PDF

Installation Procedure
1. Remove Stock Headlamps by removing the three flathead screws securing headlamp bezel in place. Disconnect and discard stock headlamp.
2. Notch the back side of the housing to obtain additional clearance for HID wiring harness to pass through. (Please See Fig. 1)
3. Insert the projection HID lamps into the housing and reinstall Headlamp Bezel. Ensure that the top of the HID lamp is facing up before securing in place.
4. Install the two wiring harness to vehicle with both black wires secured to a common vehicle ground and the two red wires secured to the batteries positive terminal post located on drivers side engine firewall.
(more…)

[Read more →]

Installation instructions for the 2003-2007 Express and Savana Vans
Use your 10-mm socket and ratchet to remove two (2) washer nuts from the inside of the small cubby hole under the radio and airbag switch. Set the washers aside. Remove two (2) 10-mm screws from the bezel below the steering column. Set the screws aside. Pull the bezel toward you releasing six (6) clips. On the pas- sengers side, remove two (2) 10-mm screws on the lower bezel below the glove box. Set the screws aside. Pull toward you to release two (2) clips and a pin that is connected to the larger radio bezel.
(more…)

[Read more →]

Remove the bezel that surrounds the climate control and extends behind the transmission shifter. To do this, grasp the bezel behind the shifter and release the first clip. In the upper-right corner of the bezel, use the Dash Trim tool to work loose the remaining ten (10) clips that hold the bezel in place. Note: On vehicles without the navigation system and/or with the DVD, the climate controls will come off with the bezel. Note: On vehicles that have the navigation system, disconnect the emergency light switch connector, and interior lighting switch. Apply the emergency brake and turn the ignition to the on position. Place the transmission shifter into the neutral position. Pull the shifter lever toward you to allow clearance for the bezel to be removed. Place the bezel aside when removed.
(more…)

[Read more →]

Begin by removing the small trim bezel that surrounds the radio. This bezel has four clips that hold it in place in each corner. Carefully use the dash trim panel tool and insert it in behind the bezel in the lower right corner. Note: Be careful not to mar the soft plastic that the bezel is made of when using the dash trim panel tool. Pull back toward you to release the lower right clip. Perform this same action in the other remaining three corners of the bezel. When the bezel is loose set it aside.
(more…)

[Read more →]

Installation instructions for the 2003 Honda Civic
- Set the parking brake and place the shifter into the drive position. Using the Dash Trim tool, pry upward to remove the inner bezel that surrounds the shifter. Remove the 2nd bezel. This bezel has a total of nine (9) clips around the edges holding it in place. Locate and remove the two (2) Phillips screws at the front of the shifter.
- Remove the cigarette lighter that extends past the shifter and on both the left and right sides. Use the Dash Trim tool and start on the left side releasing three clips, do the same on the right side releasing 3 more clips. Grasp the bezel and carefully pull toward you releasing a total of four clips. Use the Dash Trim tool to assist releasing the four clips. Once loose, remove all the wiring and set the bezel aside.
(more…)

[Read more →]

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety. Install Camera into Endgate
(more…)

[Read more →]

Before Installation of One Custom Bezel Mount and Instructions.
Begin installation by removing the dash bezel that surrounds the radio and climate control. To do this, insert the Dash Trim Tool (Part Number SIT-104) into the side of the bezel as shown in picture one. Begin with the lower right corner and release one clip. Continue by releasing the remaining 5 clips (Six total).
(more…)

[Read more →]

This is just a guideline for replacement of the gauge faces on the Ford Focus. Please don’t hold me responsible for anything that may go wrong while following these instructions. These instructions are for entertainment usage only. If you learn something from these instructions, congratulations.
1. The panel under the steering wheel will have to be removed. This is the panel to which the hood release is attached. Once this has been removed, you can access the bolts along the bottom of the panel that surrounds the gauge cluster. Don’t forget the bolt over by the headlight switch. Once the bolt shave been removed, grab the trim piece around the cluster and pull it towards you. The whole piece will unclip and separate from the dashboard. Unclip the trunk/hatch release button (if so equipped). You can now access the bolts that hold the cluster into the dash.
(more…)

[Read more →]

The RetroGauge™ Mini-Tach is designed for use with a standard ignition coil as factory fitted to 1967 and 1968 Ford Mustangs. For aftermarket ignition systems please read the important application note at the bottom of the page.
INSTALLATION
1. Disconnect the battery negative terminal from the vehicle to completely isolate the electrical system.
2. Remove the instrument cluster according the to the workshop manual (several internet resources are also available to cover this procedure)
(more…)

[Read more →]

When installing in a vehicle with an Auto Climate Control you will not be drilling or using the included screws. See step (3). When re-installing the auto climate control unit in the cavity you will need to apply some downward pressure on the unit so the centering pins and four factory screw holes will line up. Install the four (4) screws that secure the auto climate control then tighten. The mount will be nice and tight.
(more…)

[Read more →]