Automotive Manual PDF

Read all information in this manual carefully.
All suspention components are fitted and removed acc. to the manufacturer’s specifications for fitting and removing, if not otherwise required in these instructions.
Check that your vehicle type is listed in the certificate as being released for this kit.
Check the product for all components before starting installation!
(more…)

[Read more →]

In 2004 BMW started shipping the GS Adventurer with a feature that enabled the bike to be jumpstarted via a post attached directly to the starter. Prior to that you would have to remove the seat and try to access the battery which is located under the gas tank. Adding this feature to your bike is not that difficult and costs less than $30 in parts. The whole installation should take less than an hour with the majority of the time being spent locating and drilling the hole for the positive post in the starter cover.
(more…)

[Read more →]

Information inside:
1. Starting with all model year 2005 vehicles equipped with BMW Assist (except E65/66 7 Series from 3/05) now has integrated Bluetooth capability. Currently, these vehicles will be arriving at your BMW Center with Bluetooth set to active. No retrofit coding is necessary in order to use this feature.
(more…)

[Read more →]

This manual was written on your behalf in an effort to help you enjoy your new BMW Marine Engine to the maximum. No marine engine, be it the best in the world, will perform at it’s best during a long life, without proper care and maintenance. Please read this manual carefully before you set out on the first trip with your new BMW Marine Engine.
(more…)

[Read more →]

A) To remove left handlebar:
1. Remove bar end weights.
2. Cut two small cable ties holding wire loom from left control housing (PHOTO 1)­ one under the handlebar anti­ rotation bracket and the other attaching the wire loom to the underside of the top triple clamp. Do the same on the right side.
3. Remove the clutch master cylinder from the left bar.
4. Remove the forward plastic control housing cover (2 screws) Loosen the two screws that sandwich the bar between the forward plate and the rear half of the left control housing(PHOTO 2).
5. Remove the two screws attaching the left handgrip sleeve to the left bar tube­1 on top and 1 on the bottom (PHOTO 3).
6. Remove the anti rotation bracket holding screw located under the top triple clamp (PHOTO 4).
7. Loosen the two screws clamping the left bar to the triple clamp. Only the inner most crew needs to be removed to withdraw the stock bar.
(more…)

[Read more →]

BMW key programming device and software are for vehicles equiped with EWS module , coverage 1994-2004 that have EWS module(including EWS2, EWS3 and EWS3+, Rover75, MINI, RangeRover, FreeLander, Discovery).You can programm new keys when all keys are lost or stolen by this device. Of cause be able to add new keys.
(more…)

[Read more →]

The SA314 speaker bracket mounts on the left side crash bar of your motorcycle. If you have a light mounted here, the bracket mounting screws may share some or all of the mounting holes.
1. Secure the mounting brackets to the SA314 speaker using the provided hardware. Make sure that the brackets are properly oriented before proceeding.
2. Now secure the bracket onto the motorcycle using the supplied mounting hardware as shown below.
3. Connect the speaker to your siren as outlined in your siren installation manual.
(more…)

[Read more →]

On 2001 vehicles without the diagnostic connector in the engine compartment, the use of the SIA reset tool is not possible. The service indicator may be reset using the reset mode in the instrument cluster.
(more…)

[Read more →]

Vehicle: 1997 740iL, however, I think this applies to all 95-01.
Symptom: trunk may not stay fully open or may free fall when closing. In my case, the trunk would free fall closed and unless I was holding it carefully, it would slam shut.
The procedure took only about 30 minutes and was very easy. The outcome was excellent making the project well worth it and highly recommended.
(more…)

[Read more →]

The step for this BMW E65/66 Interface Installation Manual:
Caution before working
1. Before installation, be sure to key off and wait more than 5 minutes for complete discharge of electricity
2. Don’t turn on the ignition during connectors are disconnected, because if you turn on the ignition with disconnected connectors, ECU falsely recognize status of car as an error and display error code on monitor
(more…)

[Read more →]