Automotive Manual PDF

Be sure to test the heaters to make sure they work properly before going to the trouble of installing them. I just connected them to my battery terminals to do a quick test. This should only take a couple minutes and is a worthwhile precaution. Additionally, I would recommend getting some upholstery hog rings and hog pliers. These can be purchased as a package from JCWhitney for about $4-5.
(more…)

[Read more →]

1. Pull down chrome collar and carefully unscrew and remove the stock shift knob.
2. Remove the front console cover. Pull up from the front to unclip the clips and remove from the vehicle.
3. Remove the 2 screws securing the front part of the console. Remove any additional screws that may be holding the center part of the console in place, this may vary by year and model. Lift the 2 tabs shown to the right over the center section of the console so that they rest on the outside of the console assembly.
(more…)

[Read more →]

Below you will find instructions on how to install your AC Line kit for the Acura Integra DC 94-01 Chassis.
*AC Kit may not be legal for highway use. Hybrid Racing is not responsible for any direct or indirect, actual or incidental expense attributed to the use of any performance parts sold by Hybrid Racing LLC. Purchasers agree to all of the terms of this agreement upon the purchase of parts.
(more…)

[Read more →]

Acura TSX Figure Grille Installation
1) PREPARATION
1.1) Remove the OEM fog light grilles, if this item was purchased. The stock fog light opening covers are held in place with spring clips attached to the cover. Work a finger between the cover and the bumper, and pull outward to release the cover.
1.2) The lower center grille is not removable; it is bonded to the bumper, and it will be left in place.
(more…)

[Read more →]

1. Unscrew the stock shift knob by rotating it counter clockwise.
2. Remove all screws securing center console and remove console.
3. Remove the rubber dust boot surrounding the shifter, use caution not to damage it. Put it in a safe place for re-installation later.
4. Place the car up on a lift, or use a jack and jack stands to raise it off the ground. Loosen the nut on the base of the shifter using a 12mm socket and ratchet. You may need to hold the head of the bolt on the opposite side of the shift rod with a wrench to loosen the nut.
(more…)

[Read more →]

Scion xB Figure Grille Installation
1) Upper Center Grille
1.1) Remove OEM Grille. Begin by opening the hood. Remove the radiator cover that fits above the OEM grille. The radiator cover is held in place by a series of pop-top fasteners. Remove these by following the procedure shown in Figure 1. Finally, there are additional pop-top fasteners and two 10mm bolts that hold the OEM grille in place. Remove these and then remove the grille.
1.2) Prepare bumper for installation. Once the OEM grille is removed, drill two 1/8” holes in the locations shown in Figure 2. These holes will be used to secure the Figure Grille. If you ever need to re-install your OEM grille, these holes will be completely hidden and will not interfere in anyway.
(more…)

[Read more →]

Rear:
1. Raise and properly support back of car. I used a long metal bar that I had which reached across from one of the lower A-arms to the other and jacked up in the middle. I then put jack stands under the rear jacking points using jacking pucks.
2. Remove wheels
3. On the passenger’s side of the car you will need to remove the brake pipe bracket so that the suspension can be lowered. It is attached by 2 10mm nuts.
(more…)

[Read more →]

I decided to install HID’s in place of standard halogen bulbs for a little more light and I guess exterior looks. I won’t be able to see them much so I hope you other driver’s like them. Here’s the kit, a standard 35 watt HID nothing fancy conversion kit. The only extra I bought where some load resistor to clear up any “check fog light” errors I may receive.
(more…)

[Read more →]

We’re sure you’ll be pleased with the new level of performance you’ll experience. This kit should be installed on bikes with After Market Exhaust Pipes only and jetted, (not included). We recommend that an experienced mechanic perform this conversion. Use the appropriate Suzuki service manual for reference to complete jetting of carbs. Remember, gasoline is extremely flammable and can be explosive under certain conditions. Work in a well-ventilated area and clean up any spills immediately. Check for leaks before riding.
(more…)

[Read more →]

Heli Bars are designed to safely increase your riding comfort, however it is imperative that these instructions be followed to ensure correct installation. Failure to follow these instructions could result in improper installation and create a dangerous control situation.
(more…)

[Read more →]