Automotive Manual PDF

Installation Instructions. Read Me!
I) DISCONNECT NEGATIVE (-) BATTERY CABLE.
II) Remove the Factory Air Box
a) Loosen Mass Air Meter hose clamps and set meter aside.
b) Unbolt the three air box hold down fasteners and save the bolts. See Fig#1
c) Lift out & remove the factory air box assembly from vehicle.
d) Remove and save the three rubber grommets, inserts and bolts. See Fig#2
(more…)

[Read more →]

Getting started
a) Make sure vehicle is parked on a level surface, and set parking brake.
b) Disconnect negative battery terminal.
c) If engine has run within the past two hours let it cool down.

Removing the stock air inlet system
a) Remove the stock air box assembly and attaching hardware from inside the fender well.
b) Disconnect breather hose from the air inlet tube.
c) Disconnect air temperature sensor harness from the air inlet tube.
(more…)

[Read more →]

The installation of the supplied high pressure fuel pump requires removing and reinstalling the fuel tank. An automotive lift makes this job much easier. The fuel tank can be removed with the car on jack-stands, provided you have the car high enough, and an assistant ready to help you. Our recommendation is to use an automotive lift, as it is much easier. Even if you are doing this super charger installation yourself you may want to consider taking the car to your shop and have your technician install the complete fuel system which consists of the fuel pump, fuel lines, fuel filter, fuel pressure regulator as well as some minor wiring changes to the fuel system. With the new high pressure fuel system in place you will be able to drive the car home to continue the balance of the installation.
(more…)

[Read more →]

Removal of the Stock Air Intake System
a) Loosen the clamp around the throttle body using a 5.5mm socket or screwdriver. Pull the Intake Air Temperature (IAT) sensor out of the intake tube by loosening the spring loaded clamp.
b) Unplug the breather tube from the fitting underneath the intake manifold.
c) Remove the air box mounting bolt shown in the picture.
d) Remove the other air box mounting shown in the picture.
e) Carefully remove the air box assembly from the engine bay.
f) Remove the two fasteners holding the plastic cover in front of the battery.
(more…)

[Read more →]

We hope you are satisfied with the look and performance. You may use any polish or wax on the pipe as it’s painted with the same high quality paint as your car. It is also recommended to use some tire shine on the rubber elbow. Take your time and it will be a smooth install. Please review complete instructions prior to installing.

Step#
1 Verify you have all of the following parts included in the kit: (1) JLT Painted Pipe with IAC, PVC, and Vacuum line fittings, (1) 45 degree Rubber Elbow w/ clamps to connect throttle body to JLT Pipe, (1) Silicone Reducer w/ clamps to connect JLT pipe to MAF, (1) JLT heat shield, (1) Billet MAF Adaptor with bolts, (1) 4×12” S&B Air Filter, (1) 5/8” Hose, (1) 3/4” Hose, (1) Vacuum Line, (1) Silicone Spacer (for use on early Lightnings with 80mm MAF only)
(more…)

[Read more →]

Installation instructions:
1) disconnect negative battery cables from both batteries and secure so they can’t touch battery posts.
2) remove positive cable from driver’s side battery.
3) unsnap battery cover from drivers’ side. This is a real pain, sticking a screwdriver in the slot helps.
4) remove battery. Save the battery hold down bolt and block. this will be reused on the ump bracket.
(more…)

[Read more →]

Included in this kit: Inlet pipe, coupler hose, hose clamps, air filter, air filter shield, and rubber sealant strip. (2) M-4 screws.
Tools required: Small flat screwdriver or pick, 1/4″ ratchet, 8mm, and 10mm sockets, 2.5mm Allen wrench, T-20 Torx.
Step 1
Disconnect (–) negative battery terminal.
Step 2
Unplug the mass air meter by sliding the red colored locking clip back, and then squeezing the tab on the connector while pulling it from the mass air meter.
(more…)

[Read more →]

1. Disconnect negative battery cable. Remove the factory filter minder and rubber grommet from the factory intake tube, retain for re-installation later in the install.
2. Loosen the recessed bolt and remove the beauty cover. Loosen the factory hose clamps on each end of the factory intake tube and remove it from vehicle.
3. Loosen the Mass Air Flow sensor hose clamp. Remove the MAF sensor from the factory air box and temporarily set it aside. Use caution to retain the factory coupler & hose clamp on the MAF
(more…)

[Read more →]