Automotive Manual PDF

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety. Install Camera into Endgate
(more…)

[Read more →]

Before beginning installation be sure to set the parking brake and chock the wheels.
NOTE:
To ease installation and properly adjust the bar, the weight of the vehicle must be on the suspension as if driving down the road. Do not raise the vehicle by the frame.
1. Lubricate the D-bushings and place them onto the straight areas of the bar on each side of the center hump as shown in the photos.
(more…)

[Read more →]

Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body intake assembly.
3. Remove (2) bolts & save from linkage bracket. (Ref. C)
4. Remove (4) bolts from the throttle body. (Ref. D)
5. Remove gasket and clean surfaces.
(more…)

[Read more →]

Installation Instructions. Read Me!
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body intake cover.
3. Remove air intake hose assembly.
4. Remove (4) bolts from the throttle body.
5. Remove throttle linkage bracket and save screws. (Ref. “B” & “C”)
(more…)

[Read more →]

1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner assembly.
3. Remove (2) 8mm bolts from throttle linkage bracket and save. (Ref. D)
4. Remove (4) bolts from the throttle body. (Ref. C)
(more…)

[Read more →]

This manual has eight modules, covering key topics relating to Towbar electrics. Each module except 3 and 4 has a guidance section and a review section.
• Each Guidance section contains information and best practice.
• Each Review section is a form of self-evaluation chart and is to be used by the trainee during their everyday work, to judge their own performance against the standards indicated. The principle of the reviews is to harness the natural enthusiasm most people have to measure their own work against the highest standard
(more…)

[Read more →]

System is equipped with a cycling clutch system that uses an expansion valve in refrigerant line between condenser and evaporator, near condenser. System is engaged when A/C switch on control panel is pressed. See Fig. 1. Pressure switch on accumulator cycles compressor clutch on and off. Blower fan speed is controlled by sliding switch on lower left of A/C-heater control panel.
(more…)

[Read more →]

Almost every reception problem is caused by one of two things: a bad ground on the antenna, or a bad antenna cable running from the antenna to the radio.
There are (2) parts to an antenna and you have to understand the antenna cable itself. Antenna cables are coaxial style cables. Coax cables have a thin center conductor wire at the center of the cable and an outer metal braid just under the plastic jacket of the cable. The center conductor carries the signal and the outer shield serves two purposes, it shields the inner conductor from radiated noises and acts as the negative voltage path. 99% of antenna reception problems can be traced to either one of these two parts of the antenna cable.
(more…)

[Read more →]

1. Remove Air Intake Assembly and intake box from throttle body.
2. Remove the 4 nuts and studs that mount the throttle body to the intake manifold.
3. Install the JET Power-Flo throttle body spacer using the new o-ring.
(more…)

[Read more →]

Position the compact alarms and the sirens in the engine compartment, on the support of the passenger’s side shock absorber. Pass the cables through the original core hitch located in the bulkhead that divides the engine compartment and the passenger’s compartment, passenger’s side.
(more…)

[Read more →]