Tools Needed: 10, 12, 14 sockets and wrenches. You will also need a Oxygen Sensor removal tool or 22mm wrench or socket to remove the stock Oxygen sensors from the catalytic converter and install them in the new Jackson Racing header. Most of these tools are available at your local hardware or auto parts store.
IF YOU ARE NOT A COMPETENT MECHANIC, DO NOT ATTEMPT THIS INSTALLATION! ALLOW AT LEAST ONE HOUR FOR THE EXHAUST SYSTEM TO COOLBEFORE DOING ANY EXHAUST SYSTEM INSTALLATION WORK.
READ THESE INSTRUCTIONS THOROUGHLY! Follow the instruction STEP-BY-STEP, and your installation will be trouble free. If in doubt, CALL!
(more…)
[Read more →]
Removal of stock system:
1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators.
2. Using a 15mm socket or wrench, disconnect the factory exhaust system at the four bolt flange located behind the catalytic converter. If the vehicle is not equipped with a catalytic converter disconnect the four bolt flange located approximately under the passenger side seat.
3. Remove the exhaust system from the rubber insulators and remove from under the vehicle. If a hoist is not available for use, it may be necessary to cut the tail pipe behind the muffler for removal of the system.
4. Unbolt the OEM hanger from the transmission and remove.
5. Loosen the factory band clamp and remove the stock front pipe. Some vehicles are not equipped with a catalytic converter. Do not discard the band clamp as it is required for the installation.
6. Remove the spare tire. You may not be able to reinstall your spare tire after the installation of this exhaust system.
(more…)
[Read more →]
Removal of Stock System:
1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators.
2. Loosen the band clamp located behind the catalytic converter and disconnect the factory exhaust system.
3. Remove the exhaust system from the rubber insulators and remove from under the vehicle. If a hoist is not available for use, it may be necessary to cut the tail pipe behind the muffler for removal of the system.
(more…)
[Read more →]
Removal of Stock System:
1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators.
2. For 2001-2005 vehicles use a 15mm socket or wrench and disconnect the factory exhaust system at the four bolt flange located behind the catalytic converter. If the vehicle is not equipped with a catalytic converter disconnect the four bolt flange located approximately under the passenger side seat. For 2006 vehicles loosen the band clamp located behind the catalytic converter.
(more…)
[Read more →]
Read all instructions before starting any work.
1. Remove the exhaust system behind the catalytic converter assembly.
2. Grind or file the tab off the outlet end of the O.E. converter. Connect the intermediate pipe to the converter and clamp in place. This pipe will require cutting the outlet for the 133″ WB (standard cab, 8’ box). Cut to length after the muffler is in position (SEE #3).
3. Slip muffler hanger (36161) ends thru the rubber hangers. The clamp should be offset to the driver’s side. Install the muffler. The bracket clamps to the driver’s side outlet. Do not tighten yet.
(more…)
[Read more →]
Removal of Stock System:
1. Loosen the nut on the band clamp located behind the catalytic converter using a 15mm wrench or socket.
2. If a hoist is being used for the installation, the original exhaust system can be removed in one piece by removing the passenger side shock. If a hoist is not being used the tail pipe must be cut behind the muffler to be removed.
3. Remove the muffler and tail pipe from the OEM rubber hangers and separate the stock exhaust at the slip joint located behind the catalytic converter and remove the muffler and tail pipe from under the truck. Re-install the passenger side shock.
(more…)
[Read more →]
Removal of Stock System:
1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators.
2. Loosen the nut on the band clamp located behind the catalytic converter using a 15mm wrench or socket. See Figure 1.
(more…)
[Read more →]
When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
(more…)
[Read more →]
Removal of Stock System:
1. Apply a penetrating lubricant liberally to all exhaust fasteners, hangers and rubber insulators.
2. Loosen the nut on the band clamp located behind the catalytic converter using a 15mm wrench or socket.
3. Remove the muffler and tail pipe from the OEM rubber hangers. If a hoist is being used the system can be removed in one piece (more…)
[Read more →]
In an age when there is growing tension between customer expectations of high engine performance, low fuel consumption and compliance with the legal requirements on the emission of airborne pollution, the ability of a vehicle to meet the most stringent emission standards is becoming an increasingly important aspect of its market appeal.
(more…)
[Read more →]
