Automotive Manual PDF

These instructions cover both front and rear sump 289, 302, 351-W, 351-C, 429, 460 Ford, 340-360 Chrysler, Pontiac and 455 Olds. These trays are fashioned after our high-end, Big Block Chevy, competition designs which are the latest in the technology of making horsepower in the pan. Proper installation will assure the tray will make all the potential power that it is capable of.
(more…)

[Read more →]

The AD38 is a small standalone device that can overwrite the pin code stored within the skim module fitted to Chrysler/Jeep & Dodge vehicles fitted with CAN 2,3,4,5 and 6 systems. This will then allow new keys to be programmed into the vehicle. The skim module is Chrysler terminology for a combined immobiliser and aerial module. Writing a new pin code to the skim module involves removing the Skim module, which is located around the ignition barrel, from the vehicle, which is a fairly simple process.
(more…)

[Read more →]

Congratulations on your new EXeS Digital HID Conversion Kit! Please abide by your local transportation laws as this kit is intended for off road or show use purposes only. Please take your time in reading this guide as it will assist you in the installation process. Please pay attention to the exclamation marks as they have been added to alert you in an important part of the installation process and it is necessary to pay close attention to the notes following an exclamation mark.
(more…)

[Read more →]

In this chapter you will learn how to install the Neo iON in specific vehicles. Acura Before connecting any cables to the black box you must set the dip switch to the Chrysler New / Honda / Acura position. If you set the dip-switches after you have connected cables to the box, you must disconnect and reconnect them for the iON to operate. Audi Make sure you have your radio’s theft protection code before you attempt installation. When you reconnect power to the battery, you will need to enter this code. Information about the theft protection code can be found in your vehicle’s audio operation manual.
(more…)

[Read more →]

In the following cases, the vehicle may not be able to receive the registered ID code from the key. This means the engine will not start even when the registered key is turned to the START position: • When the key comes into contact with a metallic or magnetic object. • When the key comes into contact with another immobilizing key, or with some other transponder. In case like these, the theft-alarm indicator (located in the instrument cluster) will blink after 10 seconds. The theft-alarm indicator will flash for approximately 30 seconds and then go off.
(more…)

[Read more →]

This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your Crossfire. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully. Following the instruc- tions and recommendations in this manual will help assure safe and enjoyable operation of your vehicle.
(more…)

[Read more →]

You can insert the double sided keys into the locks with either side up. The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place. Ignition Key Removal The shift lever must be in PARK. Turn the key to the OFF position, then the LOCK position. Remove the key. The Sentry Key Immobilizer System does not need to be armed or activated. Operation of the system is automatic regardless of whether or not the vehicle is locked or unlocked.
(more…)

[Read more →]

Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference that may be received, including interference that may cause undesired operation. STEERING WHEEL LOCK — IF EQUIPPED Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- out the ignition key. If the steering wheel is moved no more than 1/2 turn in either direction and the key is not in the ignition switch, the steering wheel will lock.
(more…)

[Read more →]