Automotive Manual PDF

RSS Feed

The Resources for Automotive

Jeep Liberty 2″ Coil Spring Lift Spacer Installation Instructions

March 31st, 2010 · No Comments

Get ready to install front coil spring lifts.
1. Under the hood driver side.
a. Remove bolt (4), battery hold down (5), and battery (3) from battery tray (6) and vehicle. b. Remove two bolts (7), nipple (8), and battery tray (6) from inner fender (9). Do not disconnect battery tray from wiring harness (10).
c. Remove vent line (11) from nut (12).
2. Under the hood passenger side.
a. Remove four clips (13), clamp (14), and air box cover (15) from air duct (16) and air box (17).
b. Remove air filter (18) from air box (17) and vehicle.
c. Remove three nipples (8) and air box (17) from inner fender (9) and vehicle
(more…)

[Read more →]

2005-06 Hummer H3 3.5L Dynomax Kit:19425 Installation Instructions

March 6th, 2010 · No Comments

NOTE: Read all instructions before starting any work.
1. Remove the O.E. front pipe/muffler/tail pipe assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar lubricant, to aid in removing the rod hangers. The O.E. system will not come off in one piece. Cut the system between the rear axle and the muffler. Both pieces will then come off easily.
2. Install DynoMax front intermediate pipe 54374. Insert the rod hanger into the rubber isolator on the RH frame. Finger tighten the nuts on the inlet flange connection to the converter pipe.
(more…)

[Read more →]

HyperDrive Startup Guide

December 3rd, 2009 · No Comments

You will need a portable crane and/or a friend to lift the motor from the crate and on to the boat. Take your time and be careful. Keep fingers clear of pinch points near the mount and swivel.
Uncrating: Remove the handle and mount it to the side of the engine with three, 3/8″ bolts. Be careful not to stretch the handle wires and cables. The washers and nylock nuts installon the inside of the handle mount near the slots. The handle bolts must be snug enough to hold the handle firmly, but yet allow the handle to move up and down freely.
(more…)

[Read more →]

Honda GL1800 Front Mount Air Horn Installation Instructions

November 14th, 2009 · No Comments

1. Place the motorcycle on the centerstand.
2. Remove the left side cover (painted) to expose the battery. Remove the left plastic engine cover (chrome). Remove the lower center fairing cowl or spoiler; there are 2 pull pin rivets and 6 allen screws holding this panel in place. Drop the panel down and slide it out to the right or left.
3. Horns and Mounting Bracket: Attach the large “L” shaped bracket with the split clamp to the engine guards as shown in photo #1. NOTE: Make the screws snug only! Install the horn set onto the “L” bracket using the 2 allen screws provided, tighten securely. Align the horn set to be level and to have clearance between the fairing as shown in photo #2, tighten securely.
(more…)

[Read more →]

Honda 750 Shadow Aero Models Hypercharger Kit Installation

October 29th, 2009 · No Comments

A factory service manual is necessary to perform this installation. Do not attempt to perform this installation if you are not confident in your ability to perform all steps in the procedure, including precise drilling and tapping; consult a trained technician.
Procedure remove the stock aIr cleaner and carburetor
steP 1 Remove the seat, dash panel, and fuel tank; consult your factory service manual for specific instructions on performing this procedure.
steP 2 Remove the air cleaner assembly. Save the clamp securing the rubber manifold to the carburetor, it will be reused later. See PIC.1.
steP 3 Remove the carburetor for re-jetting; consult your factory service manual for specific instructions on removing the carburetor. Prepare the carburetor for re-jetting by removing the top cover, see PIC.2.
(more…)

[Read more →]

2003-2004 Honda Accord 4-Cyl. 2.4L Short Ram Intake System Installation

October 28th, 2009 · No Comments

Removal of the Stock Air Intake System
a) Loosen the clamp around the throttle body using a 5.5mm socket or screwdriver. Pull the Intake Air Temperature (IAT) sensor out of the intake tube by loosening the spring loaded clamp.
b) Unplug the breather tube from the fitting underneath the intake manifold.
c) Remove the air box mounting bolt shown in the picture.
d) Remove the other air box mounting shown in the picture.
e) Carefully remove the air box assembly from the engine bay.
f) Remove the two fasteners holding the plastic cover in front of the battery.
(more…)

[Read more →]

2001-2004 Chev/GMC Duramax Diesel “Cool Duals” Installation Instructions

October 14th, 2009 · No Comments

Removal of stock system:
First using 15mm socket or wrench, remove four (4) nuts at flange located approximately under the passenger side seat. Remove rear exhaust from rubber hangers and remove the system from under the truck.
NOTE: If you have purchased the optional front pipe, Remove the stock front pipe on the truck by removing the exhaust hanger on the transmission using a 13mm socket, then remove the band clamp at the front of the pipe, then remove stock front pipe from the truck. ( Note: the band clamp will be re-used during the installation of your new MBRP system)
(more…)

[Read more →]

2007 Cadillac Escalade 6.2L AWD 4dr Cat-Back Single Exhaust Installation Instructions

October 3rd, 2009 · No Comments

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.

SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

Chevrolet/GMC 1500 Short & Long Bed 2500 Light Duty Short Bed Installation

September 15th, 2009 · No Comments

Installation Instructions
1. Figure 2 shows a cable bracket which holds a brake line to the inside of the frame rail. Loosen this bracket from the top of the frame and move the brake line down about 1/2” so that it is not interfering with hitch cross members.
2. From underneath the passenger’s side of vehicle remove or cut out the section of the heat shield that is located between the frame rails and the bed of the vehicle.
(more…)

[Read more →]

Light Bar Mounting Instructions

September 12th, 2009 · No Comments

LIGHT BAR CUTTING INSTRUCTIONS
1. Two people will be needed to complete this task.
2. Place ONLY THE MOUNTING END CASTING into the rain-gutters of your vehicle.
3. Level each Mounting End Casting so that the top flat area is parallel to the horizon.
4. Take a tape measure and measure the distance between each open end of each Mounting End Casting .
5. Add 2 inches to that dimension.
6. Subtract that total from the total length of the bar, which is 56″.
7. Take the difference and divide it by two.
8. The amount divided by two is the amount you will cut off each end of your bar.
(more…)

[Read more →]