Automotive Manual PDF

RSS Feed

The Resources for Automotive

1999 Chevrolet Silverado 1500 base Truck will a cold air intake really improve the fuel economy?

June 30th, 2013 · No Comments

I have a 1999 Chevrolet Silverado 1500 base Truck will a cold air intake really improve the fuel economy? It is a 4.8 L V8 and it only gets like 14-16 mpg city, i was wondering if a cold air intake, or anything else would improve the gas mileage.
(more…)

[Read more →]

How can i increase gas mileage on 1994 Chevrolet Silverado?

January 7th, 2011 · No Comments

I have a 1994 Chevrolet silverado. i was trying to find ways of making its fuel last longer!
- For starters I would get some sea-foam and run some through the intake vacuum hose as instructed on the can then add the rest to the gas tank. After doing that I would be sure to keep up on regular maintenance like changing oil, (more…)

[Read more →]

How do I increase my Horsepower for 2005 Cadillac Deville DHS?

December 27th, 2010 · No Comments

I have a 2005 Cadillac Deville DHS V8 North star Engine 275 Horsepower
I want to increase my overall horsepower for my car. I know there are many different methods I’m just curious as to which method is best for doing this. I have heard Performance chips can work but are often fakes or scams of some sort. I know I could supercharge or turbo it but I do not want to spend thousands of dollars. Ideas?
(more…)

[Read more →]

How different is an 09 Dodge Dakota engine from the previous year models?

December 21st, 2010 · No Comments

I’d like to put a cold air intake into my 09 Dodge Dakota, but apprently its too new for many after market parts and they only go till 08…
is there a big difference in the engine or will an 08 intake work in my 09?
(more…)

[Read more →]

1994 Chevrolet S10 Blazer short ram air intake?

December 21st, 2010 · No Comments

I’m looking to install a Short Ram air intake on my Blazer. With a typical kit, do I have to mess with the MAF and intake sensors with the installation? I looked at the intake system on my Blazer, and it appears as if all of the sensors are positioned between the throttle body and the tubing for the intake, not on the intake itself. But I’m not completely sure. Has anyone here installed a short ram or even a cold air intake on one of these before?
(more…)

[Read more →]

2003-2005 Hyundai Tiburon V6 Short Ram System Instructions

March 24th, 2010 · No Comments

Removal of the stock intake system.
a. Remove the upper plastic cover covering the stock intake system.
b. Remove the hose clamp securing the upper filter box to the air flow sensor. Unlatch the two clips securing the upper filter box and remove.
c. Remove the filter. Remove the three bolts securing the lower filter box and remove from vehicle.
d. Kit removed from vehicle.
(more…)

[Read more →]

2002-2005 Honda Civic Si Cold Air System Installation Instructions

November 12th, 2009 · No Comments

Our system is constructed of lightweight aluminum and then painted with a zirconia based powder coat for superior heat insulating characteristics. The aluminum will not crack in extended use like plastic and it is actually lighter than plastic. The tube diameter and length are matched for each engine to give power over a broad rpm range. Unlike the plastic systems that use a continually diverging cross section, we take advantage of the acoustical energy in the duct to promote cylinder filling during the intake valve-opening event.
(more…)

[Read more →]

2004-05 Honda Civic L4-1.6L Typhoon Cold Air Intake System Installation Instructions

November 5th, 2009 · No Comments

TO START:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the air temperature sensor electrical connection as shown.
3. Unclip the battery cable from the air inlet duct as shown.
4. Loosen and remove the two bolts that secure the air inlet duct as shown.
5. Remove the air inlet duct.
6. Loosen and remove the four bolts that secure the air intake resonator.
(more…)

[Read more →]

00-Up Honda S2000 Cold Air Intake Installation Guide

November 1st, 2009 · No Comments

Removal of Factory Intake
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Unclip the six over center clamps, then remove the air cleaner lid.
3. Remove the air injection pump hose from the stock intake tube.
4. Remove the crank case vent hose from the stock intake tube.
5. Loosen the hose clamp at the throttle body, then remove the intake tube and filter.
6. Remove the solenoid from the lower air cleaner assembly.
7. Unclip the wire harness from the lower air cleaner assembly.
8. Unclip the vacuum hose from the rear of the lower air cleaner assembly.
9. Remove the three bolts that secure the lower air cleaner assembly.
10. Remove the lower air cleaner assembly.
11. Remove the stock rubber hose from the crank case vent on the cam cover and from the hard line.
(more…)

[Read more →]

2004-2006 Chevy Colorado Brute Force Intake System Installation Instructions

September 16th, 2009 · No Comments

Getting Started
a) Make sure vehicle is parked on a level surface. Set parking brake.
b) Disconnect negative battery terminal from the battery.
c) If engine has run within the past two hours, let it cool down.

Removal of the stock intake system.
a) Before removing any of the O.E. components, label each individual part so that no components become mixed up during the installation process.
(more…)

[Read more →]