Automotive Manual PDF

These instructions are to insure proper installation, which will enhance the safety and reliability of your Jet Trax System. The Jet Trax System is designed to provide years of dependable service without undue maintenance cost or operations problems. By following these step-by-step instructions, your Jet Trax System will become a secure and reliable transporting and loading device.
(more…)

[Read more →]

When we say complete, we mean COMPLETE. All kits come with a solid mass flywheel, disc, pressure plate assembly, alignment tool, pilot bearing already pressed in the flywheel, release bearing, as well as all new flywheel bolts, washers(where applicable) and clutch mounting bolts.
(more…)

[Read more →]

The AD38 is a small standalone device that can overwrite the pin code stored within the skim module fitted to Chrysler/Jeep & Dodge vehicles fitted with CAN 2,3,4,5 and 6 systems. This will then allow new keys to be programmed into the vehicle. The skim module is Chrysler terminology for a combined immobiliser and aerial module. Writing a new pin code to the skim module involves removing the Skim module, which is located around the ignition barrel, from the vehicle, which is a fairly simple process.
(more…)

[Read more →]

Dodge Charger Figure Grille Installation
Figure 1. Examples of low-profile Philips screwdrivers. 1) Ratchet (¼” drive) with ¼” socket and Philips bit. 2) Offset Philips screwdriver.
1.1) Remove radiator covers. Begin by popping the hood of your vehicle. There are two plastic protective shields which cover the radiator area. These are held in place by small clips which will let go easily by pulling on the pieces. Fig. 2 shows these covers and illustrates their removal.
(more…)

[Read more →]

Congratulations on your new EXeS Digital HID Conversion Kit! Please abide by your local transportation laws as this kit is intended for off road or show use purposes only. Please take your time in reading this guide as it will assist you in the installation process. Please pay attention to the exclamation marks as they have been added to alert you in an important part of the installation process and it is necessary to pay close attention to the notes following an exclamation mark.
(more…)

[Read more →]

This document explains injector removal, nozzle swap, and injector reinstallation on a VW TDI. The car used was a 2001 Golf (ALH engine). The instructions should be similar for earlier TDI engines (AHU and 1Z). I welcome email with comments or questions about the content of this howto!
(more…)

[Read more →]

Measure from the center of the wheel up to the bottom edge of the wheel opening
LF______ RF______ LR______ RR______2.
NOTE: The factory service manual specifically states that striking the knuckle to loosen the ball joints or tie rod ends is prohibited. Striking the aluminum knuckle can damage it. A special puller tool #8677 (or equivalent ball joint tool) is recommended to be used to separate these components from the knuckle.
(more…)

[Read more →]

1. Remove the negative battery cable first, then the positive battery cable. If equipped, the Supplemental Restraint System will be deactivated when the battery is disconnected.
2. Measure and record the space between the bumpers and the body as well as the space between the cab and bed for reference during installation of this kit.
(more…)

[Read more →]

Congratulations! You have purchased the finest street Supercharger available for the 1997/2001 5.2/5.9L Dodge engine. The centerpiece of this kit is the highly efficient and reliable Paxton Automotive Corp. NOVI 2000 supercharger. A mechanically driven (by belt) centrifugal blower (supercharger). This kit comes with all of the parts you’ll need for a successful installation. The operations required have been grouped in order of sequence.
(more…)

[Read more →]

The purpose of this kit is to indicate to the driver with the red/amber LED, if the supply fuel pressure of the VP44 injection pump is dropping below 5psi. Also note that damage may result to the VP44 if it is starved for fuel. If you are finding that your existing setup cannot supply enough fuel for the VP44, you may want to look at some additional kits to protect your system.
(more…)

[Read more →]