Automotive Manual PDF

RSS Feed

The Resources for Automotive

BMW 520i couldn’t start, I know it may be a battery but in this car,the battery is no where to be?

September 30th, 2012 · No Comments

This BMW 520i is a M reg (1994).The battery isn’t in the engine compartment nor in the back bonnet.Tried and failed to find where the battery is situated.

- I am pretty sure on that model the battery is in the boot or trunk whichever you call it as you look in on the right side with a cover over it that makes the floor level to the sides.
(more…)

[Read more →]

What is the average selling price of a 1970 Volkswagen Beetle?

December 24th, 2010 · No Comments

I have found a private seller in my area selling one for $4750. Its restored fairly nicely and has about 111,000 miles on it, I think. I have pictures if anyone wants to help me out seriously! I want to haggle him down, but besides not knowing how to do so, I have no bases for comparison as far as price, so any help would be useful.
(more…)

[Read more →]

Hummer H2 Powerstep Installation Instructions

February 18th, 2010 · No Comments

Step One
REMOVE CANISTER PURGE VALVE BRACKET AND ROCK RAIL
Remove the Canister Purge Valve Bracket from the Rock Rail. Set the bolt aside to be reused later. Then remove the ten bolts that secure the Rock Rail to the vehicle. Set these bolts aside also. Some of them will be used again later
Step Two
INSTALL NEW CANISTER PURGE VALVE BRACKET
Locate the 4th set of holes from the front on the inner sill. Place the Canister Purge Valve Bracket from the Parts Kit over the holes and install it with the bolt that was removed in Step One. Install the Canister Purge Valve on the bracket using an M8 x 20 Bolt, Nut and Washer.
(more…)

[Read more →]

Hummer H3 Delta 6X Light Bar Installation Instructions

January 9th, 2010 · No Comments

Step 1
Remove the driver’s side hood cover by prying upward with both hands.
Step 2
Remove the driver’s side windshield molding. Do not peel off the rubber seal or separate from roof molding.
Step 3
Remove 4 screws from driver’s side roof railing. Remove roof and windshield molding and set it down on the table.
Step 4
Measure 1” from the beginning of the roof railing and mark on the masking tape the spot to drill ―” hole for your harness.
(more…)

[Read more →]

2002-04 Honda Civic Si Race Header Installation Instructions

November 27th, 2009 · No Comments

Tools Needed: 10, 12, 14 sockets and wrenches. You will also need a Oxygen Sensor removal tool or 22mm wrench or socket to remove the stock Oxygen sensors from the catalytic converter and install them in the new Jackson Racing header. Most of these tools are available at your local hardware or auto parts store.

IF YOU ARE NOT A COMPETENT MECHANIC, DO NOT ATTEMPT THIS INSTALLATION! ALLOW AT LEAST ONE HOUR FOR THE EXHAUST SYSTEM TO COOLBEFORE DOING ANY EXHAUST SYSTEM INSTALLATION WORK.
READ THESE INSTRUCTIONS THOROUGHLY! Follow the instruction STEP-BY-STEP, and your installation will be trouble free. If in doubt, CALL!
(more…)

[Read more →]

1992-1995 Honda Civic with B16A Hybrid Intake System Installation Instructions

November 15th, 2009 · No Comments

The AEM Hybrid Intake System is the result of extensive development on a wide variety of hybrid cars. Each system is engineered for the particular application. The AEM Hybrid Intake System differs from all others in several ways. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Hybrid Intake Systems come with complete instructions for ease of installation.
(more…)

[Read more →]

1996-00 Honda Civic EX Cold Air System Installation

November 12th, 2009 · No Comments

Getting started
a) Make sure vehicle is parked on a level surface, and set parking brake.
b) Disconnect negative battery terminal.
c) If engine has run within the past two hours let it cool down.

Removing the stock air inlet system
a) Remove the stock air box assembly and attaching hardware from inside the fender well.
b) Disconnect breather hose from the air inlet tube.
c) Disconnect air temperature sensor harness from the air inlet tube.
(more…)

[Read more →]

1996-2000 Honda Civic w/ B18C1 Hybrid System Intake Installation Instructions

October 30th, 2009 · No Comments

The AEM Hybrid Intake System is the result of extensive development on a wide variety of hybrid cars. Each system is engineered for the particular application. The AEM Hybrid Intake System differs from all others in several ways. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Hybrid Intake Systems come with complete instructions for ease of installation.
(more…)

[Read more →]

99-07 Chevy & GMC Full Size Part # 000937, 000938 Installation Instructions

October 13th, 2009 · No Comments

REMOVAL:
1. Engage the steering column / ignition switch lock with the steering wheel & wheels centered. (NOTE It may be necessary to remove the upper and lower steering shaft bolts prior to locking for accessibility)
2. Remove the two bolts holding the upper shaft in place. One is located in the engine compartment; the second is located under the dash at the base of the steering column.
3. Compress factory shaft assembly and remove it from under the dash. Do not spin wheel with shaft removed.
(more…)

[Read more →]

2004 Chevy HD Truck Duramax Diesel High Output “LLY” Installation Instructions

October 12th, 2009 · No Comments

Tools Required For Installation:
Flat Head Screwdriver
8mm, 10mm Socket
Ratchet & Extension
3/32”, 5/32” Allen Wrench
#T20 Security bit (Included)
1. Disconnect the negative battery cable. Disconnect the Mass Air Flow (MAF) sensor wiring harness. Using the supplied T-20 Security bit, remove the two screws and the Mass Air Flow sensor from the tube (save the sensor for reuse). Loosen the hose clamps on each end of the factory intake tube assembly.
(more…)

[Read more →]