Automotive Manual PDF

1. Attach the left strake to the side under spoiler using the three self-tapping screws.
2. Remove the three self-tapping screws that fasten the front inner fender to the fenderwell.
3. Remove the four clips that fasten the existing side under spoiler to the side sill, then remove the spoiler by sliding it toward the front.
4. Remove the spring nut from the end of the side under spoiler you just removed.
5. Remove the eight clips from the side sill by turning them 45 degrees.
(more…)

[Read more →]

Do not smoke or be near open flame while performing installation. Wear eye protection as the fuel system is under pressure.
Kit includes
• Installation bracket, fuel line disconnect tool, and cable/zip ties.
• EFI multi port fuel injection hose and fuel line quick connect fittings.

Installation Procedure
• Unscrew the gas cap to release residual pressure in the fuel system.
• Locate the fuel RETURN line (smaller of the 2 lines) containing the fuel line quick connect fitting. This connection is located at the rear of the engine near the fire wall on the driver’s side. This kit is designed for mounting location of the driver’s side stud on the master brake cylinder stud.
(more…)

[Read more →]

Do not smoke or be near open flame while performing installation. Wear eye protection as the fuel system is under pressure.
Kit includes
• Installation bracket, fuel line disconnect tool, and cable/zip ties.
• EFI multi port fuel injection hose and fuel line quick connect fittings.

Installation Procedure
• Screw the 90* fittings into the top and bottom of the Fitch unit. Tighten down the lock nut on the 90* fittings.
• Using the 18” hose with the female plastic fitting, screw the opposite end to the 90* fitting at the top of the Fitch unit and the 6” male hose to the bottom of the Fitch unit.
(more…)

[Read more →]

Do not smoke or be near open flame while performing installation. Wear eye protection as the fuel system is under pressure.
Kit Includes
Installation bracket/s, cable ties EFI multi port fuel injection hose with Male/Female quick connect fittings (Not included – Ford Fuel Line disconnect tool No. 7336 – available at your local Ford Dealer or see page 3 of the installation instructions)
(more…)

[Read more →]

Why our nitrous system is better:
• A complete 1999-2004 Mustang GT specific nitrous system. Everything is included in this kit for a safe, easy, plug and play installation.
• Adjustable from 75-175 horsepower. Safe enough for stock engines, powerful enough for racing use.
• Uses a custom made Ford fuel rail adaptor. This component gives easy access to the fuel system for nitrous system hook-up, especially the 2003-04 models.
• The 1999-2004 Mustang GT Nitrous System is activated at wide open throttle with advanced electronics that monitor your throttle position sensor (TPS); easy and safe activation.
• Unique nozzle design has “Active Fuel Control™” built in. This feature monitors bottle pressure and when the nitrous system is engaged, it adds or subtracts enrichment fuel so the engine never runs too rich or too lean.
(more…)

[Read more →]

The instructions given below cover normal operation of your vehicle and must be carefully observed. By following these rules you will enhance your own safety and the safety of those around you. You will also maximize the life and utility of your vehicle. Two wheeled vehicles obviously do not provide some of the protection provided by automobiles, therefore it is essential that you wear appropriate protective clothing.
(more…)

[Read more →]

Walt’s 2001 Acura® MDX comes into your shop complaining that the dashboard is creaking. Just the thought of crawling under the dashboard of Walt’s Acura makes your back start creaking. Fortunately, you don’t have to be a contortionist to perform this repair. The fix involves removing the front damper/spring assembly, grinding off body spot weld burrs and refinishing the surface, and/or installing self adhesive shims (Acura P/N 75826-634-300, H/C 0701896) three per side, to the damper mounting base.
(more…)

[Read more →]

At Synapse Motorsport Inc. we are frequently asked to fabricate parts. Since there is a lot
of interest in these techniques I thought I’d show a few techniques to help you along.
This should take the mystery out of carbon fiber. This high tech material can easily be used to add that special effect to your car. The investment in materials is small and the procedures used do not require any high tech equipment. If you follow along you will be able to make your own parts.
(more…)

[Read more →]

What you do before you start a trip goes a long way toward determining whether or not you’ll get where you want to go safely. Before taking off on any trip, a safe rider makes a point to: 1. Wear the right gear. 2. Become familiar with the motorcycle. 3. Check the motorcycle equipment. 4. Be a responsible rider. WEAR THE RIGHT GEAR When you ride, your gear is “right” if it protects you. In any crash, you have a far better chance of avoiding serious injury if you wear:
(more…)

[Read more →]