Automotive Manual PDF

RSS Feed

The Resources for Automotive

LSx Subframe and Axle Kits for Mazda Miata Boss Frog Installation Instructions

August 18th, 2010 · No Comments

You have purchased one of the highest quality engine swap subframe kits available today. Installing your new drivetrain involves many steps, but is really not that difficult if you take your time and understand what you are trying to accomplish. These instructions will clearly illustrate the methods we have found to work the best. If something does not fit properly, we would like to know about it, so that we can improve our products.
(more…)

[Read more →]

Jeep Wrangler TJ Pocket Style Flare Set Installation Instructions

April 5th, 2010 · No Comments

FLARE INSTALLATION PROCEDURES
Step 1: Painting (Optional)
(A) It is recommended that painting be done prior to installation.
(B) Clean outer surface with a high-grade degreaser. DO NOT USE LACQUER THINNER OR ENAMEL REDUCER AS A DEGREASER. Wipe outer surface thoroughly with a tack rag prior to painting.
(C) Paint flares with a polypropylene primer, and let the primer flash
(D) Paint flares with a high build primer.
(E) Color coat must have a flex additive to prevent paint cracking.
(F) Paint flares using a high quality lacquer, enamel, or polyurethane automotive paint and clear coat.
(more…)

[Read more →]

2003-2005 Hyundai Tiburon V6 Short Ram System Instructions

March 24th, 2010 · No Comments

Removal of the stock intake system.
a. Remove the upper plastic cover covering the stock intake system.
b. Remove the hose clamp securing the upper filter box to the air flow sensor. Unlatch the two clips securing the upper filter box and remove.
c. Remove the filter. Remove the three bolts securing the lower filter box and remove from vehicle.
d. Kit removed from vehicle.
(more…)

[Read more →]

Hummer H2 Rear Mud Guards Installation Instructions

February 18th, 2010 · No Comments

It may be necessary to remove the wheels depending on the tools being used for installation.
1. Clean and degrease the mud guard location area on the fender before installation.
2. Remove factory fasteners from locations A and B (Figure 1).
3. Place mud guard against fender and install #10 screws and washers at locations A and B, through mud guard, through existing fender holes and into u-clips. NOTE: The u-clips are to be used as a nut and not to be clipped over fender. Check fit and level before tightening.
4. Using mud guard as a template, drill an 1/8” hole at location C and install a #10 screw.
(more…)

[Read more →]

2008 Hummer H3 Alpha, 5.3L, 4wd Cat-Back Split Rear Exhaust Installation Instructions

February 15th, 2010 · No Comments

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

03-05 Hummer H2 P/N 200-183 Installation Instructions

February 15th, 2010 · No Comments

Installation Instructions. Read Me!
I) DISCONNECT NEGATIVE (-) BATTERY CABLE.
II) Remove the Factory Air Box
a) Loosen Mass Air Meter hose clamps and set meter aside.
b) Unbolt the three air box hold down fasteners and save the bolts. See Fig#1
c) Lift out & remove the factory air box assembly from vehicle.
d) Remove and save the three rubber grommets, inserts and bolts. See Fig#2
(more…)

[Read more →]

06-07 Hummer H3/2005-2007 Colorado/Canyon 4wd Level Lift Installation Instructions

February 9th, 2010 · No Comments

Step I:
Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground using a floor jack and jack stands or a (2) two post lift if available.
First, remove driver side front wheel, then unbolt upper shock mounting nut.(A) Next remove lower shock mounting nut and bolt.(B) Remove shock. Install shock stem spacer provided and reinstall bushings and shock.(C) & (D) Verify that all fasteners have been tightened to the proper torque specs and reinstall wheel.
*Be sure to torque the lug nuts to the proper OEM settings.
(more…)

[Read more →]

2006-2009 Hummer H3 & 2005-2009 Colorado/Canyon 4WD Torsion Key Kit Installation Instructions

January 6th, 2010 · No Comments

Step 1: Applies to H3 ONLY, for Colorado/Canyon please skip to step 2.
Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground using a floor jack and jack stands or a (2) two post lift if available.
First, remove driver’s side front wheel, then unbolt upper shock mounting nut. (A)
Next remove lower shock mounting nut and bolt. (B)
Remove shock. Install shock stem spacer provided and reinstall bushings and shock.
Verify that all fasteners have been tightened to the proper torque specs and re-install wheel.
*Be sure to torque the lug nuts to the proper OEM settings.
(more…)

[Read more →]

Bulk Instructions Simple

December 5th, 2009 · No Comments

To get the most life and performance from RaceTEX bulk muffler packing, a mu ffler should be repacked with the core in it. Ideally, you would like to fill the front of the muffler first (the end closest to the engine) and work towards the exit. This isn’t always possible as with mufflers that have cores welded to the rear end-cap (Honda CRF150R, White Brothers E-Series for example).
(more…)

[Read more →]

2006 Honda Ridgeline PART#57600 57601 Bull Bar Installation Instructions

November 19th, 2009 · No Comments

PROCEDURE:
1. Remove push type retainers from lower splash shield. Remove plastic splash shield to access to mounting location.
2. Locate and remove bolts that hold the frame brace and bumper brackets to vehicle.
3. Install frame bracket between lower radiator support and frame brace using (3) existing bolts. As shown.
4. Cut plastic splash shield to allow brackets to pass through. See Cutting Instruction sheet for guidelines on cutting. Reinstall plastic splash shield over brackets in this same order removed.
(more…)

[Read more →]