Automotive Manual PDF

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Determine driver and passenger Mounting Brackets.
3. Hang the inner side of the driver front Mounting Bracket into position by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame (Figure 1). NOTE: There are two threaded holes by the front mounting location on the frame, use the one towards the rear of vehicle.
4. Attach the opposite side of the driver front Mounting Bracket to the threaded holes on the floor panel of the vehicle by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers (Figure 1).
5. Locate and cut out the openings in the driver and passenger side trimming templates with a pair of scissors (Page 3 & 4)
6. Fit the driver’s side template onto its respective side plastic rock shields. Position them using two each of the 8mm bolts that will later be used to mount the side bar brackets. Transfer the openings in the templates onto the plastic cover using a magic marker.
7. Now remove the rock shield from the undercarriage of the car. The three front screws can be removed with a 10MM socket. The plastic retainer plugs can be removed with a flat blade screwdriver.
8. Using a sharp knife or pair of shears, cut out the shields as marked using the templates (Figure 2).
9. Insert the inner side of driver rear Mounting Bracket through previously cut out hole on the plastic cover. Hang Mounting Bracket by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame (Figure 3). NOTE: There are two threaded holes on the frame, use the one towards the rear of vehicle.
10. Attach the opposite side on the driver rear Mounting Bracket by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers into factory threaded holes on the floor panel.
11. Position Driver Side Bar onto Mounting Brackets. Attach Side Bar to Mounting Brackets using the included (4) 8mm x 30mm Hex Head Bolts, (4) 8mm Lock Washers, and (4) 8mm Flat Washers (Figure 1). Do not tighten at this time.
12. Level and adjust Side Bar; then tighten all hardware at this time.
13. Re-install the rest of fastener on the rock shield.
14. Repeat steps 2-13 for passenger Side Bar.
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Get pdf

[Read more →]

1. Remove contents and check for damage. Verify all parts are present. Read instructions completely before installation.
2. Locate driver side mounting locations on vehicle (See Figure 1and 2). Repeat for passenger side.
3. Attach driver side front and rear mounting brackets to underside of rocker panel as shown using M8 hex bolts, 5/16” flat washer and 5/16” lock washer. Hand tighten only (See Figure 1 and 2). Repeat for passenger side.
(more…)

[Read more →]

The Gear Box is designed to fit under the rear seat of your truck or SUV. The Gear Box gives you a place to store loose items and clutter and ultimately help keep your vehicle organized. It’s designed to fit your vehicle with or without your Husky Liners in place and only takes a few minutes to install.

INSTRUCTIONS
1) Open and remove the Gear Box from the shipping box and protective plastic bag.
2) Lift the rear seats into their upright position.
(more…)

[Read more →]

BRACKET MOUNTING INSTRUCTIONS
Step 1. Remove contents from box and check for damage. Verify all parts against parts list. Read and understand instructions completely before installation.
Step 2. Position and hold template on passenger side for quick latch bracket as shown (See Figure 1). (FOR TOYOTA, NISSAN, CHEVY S-10, GMC up to 94, and MAZDA up to 94 a separate bracket kit must be ordered). Using a center punch, punch each hole. NOTE: If the truck has a bed liner, center punch the bed liner. DO NOT CUT THE BED LINER! Repeat for driver side.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list. Read and understand instructions completely before beginning installation.
STEP 2. Position and hold template on passenger side for square bracket as shown (See Figure 1). (FOR TOYOTA, NISSAN, CHEVY S-10, GMC up to ‘94, and MAZDA up to ‘94 Use template for “L” bracket as shown in Figure 4). Using a center punch, punch each hole. NOTE: If the truck has a bed liner, center punch the bed liner. DO NOT CUT THE BED LINER! Repeat for driver side.
STEP 3. Verify hole locations before drilling (See Figure 2). Drill mounting holes for square brackets using 9/64” drill bit (See Figure 2). For “L” bracket mounting, drill mounting holes using 7/32” drill bit (See Figure 4). Repeat for driver side.
(more…)

[Read more →]

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not required, but strongly recommended. If local/state law requires a license plate, license plate relocation kit is available.
3. From underside of vehicle, remove the two bolts holding the driver factory tow hook, then remove tow hook from vehicle. NOTE: This Bull Bar is not compatible with factory tow hooks, so you will not be reinstalling factory tow hooks back onto vehicle.
(more…)

[Read more →]

Preparing the Vehicle
1. Elevate the truck and place the frame securely on jack stands.
2. Remove the wheels.
3. Disconnect the sway bar links from each lower control arm.
4. Remove the shock absorbers.
NOTE: We recommend using a Bell Tech drop spindle or equivalent along with this installation
(more…)

[Read more →]

Before any tear-down or disassembly begins, it is important to verify which bearing you have. There are two types of “Green Bearings” being supplied by axle manufacturers. Your setup should look like Figure 2 (below left), not the Figure 1 configuration, otherwise this kit will not fit. Furthermore, review the wheel clearance diagram (Figure 3, below right) to verify that there is adequate clearance with the wheels you will be using with this installation.
(more…)

[Read more →]

Congratulations on purchasing the finest hood hinge kit made. We are very proud of this kit, and you will be too! We have tried to make the installation as easy as possible. Most of the kit is pre-assembled to help you out. You will need tools, a drill, and 1/8”, 1/4”, and 3/8” bits, and a round file.

1. When the hood closes with the new hinge, it locks down with the stock hood latch. The safety latch, or secondary latch is no longer needed, so remove it.
(more…)

[Read more →]

Before beginning installation, familiarize your-self with the installation instructions and the ultrasonic parking assist system components.
To ensure your safety:
A) Make sure your vehicle is in “PARK”.
B) Apply the emergency brake.
C) Read this manual before starting.

CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting.
(more…)

[Read more →]