Automotive Manual PDF

This is just a guideline for replacement of the gauge faces on the Ford Focus. Please don’t hold me responsible for anything that may go wrong while following these instructions. These instructions are for entertainment usage only. If you learn something from these instructions, congratulation.

REQUIRED TOOLS:
7mm Hex wrench, socket extensions, Torx T-8 driver, black permanent felt tipped marker.
(more…)

[Read more →]

You have just purchased the BEST adjustable cam sprockets available. These AEM billet aluminum adjustable cam gears are CNC machined from billet aluminum and then laser etched with cam timing marks for adjustment up to ±10° at the cam or ±20° at the crankshaft. Using the vernier scale on the sprocket hub helps to do the cam timing changes quickly and accurately. The inner hub is anodized for lasting beauty and resistance to corrosion. The out gear sector is hard anodized for resistance to wear. We have found that there are significant power gains to be made by adjusting the cam timing even with stock cams and compression. Adjustable cam sprockets are usually required in applications where an aftermarket or reground performance cams are installed or the cylinder head has been milled 0.005” or more. The use of these cam sprockets allows the extraction of maximum power from your engine. We have recorded gains of up to 1015 horsepower due to cam timing tuning using adjustable cam sprockets.
(more…)

[Read more →]

This is just a guideline for replacement of the gauge faces on the Ford Focus. Please don’t hold me responsible for anything that may go wrong while following these instructions. These instructions are for entertainment usage only. If you learn something from these instructions, congratulations.
1. The panel under the steering wheel will have to be removed. This is the panel to which the hood release is attached. Once this has been removed, you can access the bolts along the bottom of the panel that surrounds the gauge cluster. Don’t forget the bolt over by the headlight switch. Once the bolt shave been removed, grab the trim piece around the cluster and pull it towards you. The whole piece will unclip and separate from the dashboard. Unclip the trunk/hatch release button (if so equipped). You can now access the bolts that hold the cluster into the dash.
(more…)

[Read more →]

The AEM Short Ram Air Intake System is the result of extensive development on a wide variety of cars. It is the most advanced short pipe air intake system on the market. Each system is specifically engineered for its particular application. All AEM Short Ram Air Intake Systems deliver maximum performance gains through lightweight, all- aluminum, mandrel-bent tubing that is tuned in both length and diameter. The aluminum will not crack in extended use like plastic. The tube length and diameter are matched for each specific engine to give power over a broad RPM range. Unlike plastic systems that use a continually diverging cross-section, we take advantage of the acoustical energy in the inlet duct to promote cylinder filling during the intake valve- opening event. Every intake is coated with a high-gloss, heat-reducing Zirconia based powder coating.
(more…)

[Read more →]

The AEM Cold Air System is the result of extensive development on a wide variety of cars. Each system is engineered for the particular application. The AEM Cold Air System differs from all others in several ways. We take the inlet air from outside of the engine compartment where the inlet air is considerably cooler than the hot under hood air. The cooler inlet air temperature translates to more power during the combustion process because cool air is denser than warm air. AEM has conducted extensive inlet air temperature studies and we have seen temperature reductions of up to 50 degrees by pulling air from outside of the engine compartment. The air mass flow to the engine is increased because of the increased airflow and reduced inlet temperature, which translates to more power. The AEM Cold Air Systems are 50 states Street Legal (some model and years still pending) and come with complete instructions for ease of installation.
(more…)

[Read more →]

Do not perform this install near a flame source due to the risk of fire or explosion from gas fumes. Use a jack to lift rear of vehicle. Remove the passenger side rear tire. Remove the wheel well cover to expose the fuel filler neck behind the quarterpanel.
Note: For manual locking or manual non-locking fuel doors, do steps 1-4 only. For electric locking fuel doors, do all steps.
(more…)

[Read more →]

Please gather the following tools before you begin the installation: * Power Drill. * 3/16 drill bit. * Large flat head screw driver. * Large Phillips head screw driver. * Sharp utility knife or razor blade. * Fine permanent marker. * Center punch & hammer - optional. Step 2 - Unpack Dead Pedal kit and verify contents. Remove all items from the the shipped package. Copyright © 2003 Redline Tuning LLC. All Rights Reserved. You should have the following before beginning: * RedlineTuning Focus Dead Pedal * (2) Washers * (2) Sheet Metal Screws * Printed Installation Instructions
(more…)

[Read more →]

Gather required tools. Please gather the following tools before you begin the installation: * Power Drill * Utility Knife. * 3/16 drill bit. * Duct Tape * 9mm or 11/32 open ended wrench. * Pliers. * 9/64″ Hex Key or Allen Head wrench * Small piece of cloth. * Flat file for filing metal. * Zip tie - medium size. * Rasp file or round file. * Body color touch up paint. * Fine permanent marker. * Phillips screw driver. Step 2 - Unpack fuel door kit and verify contents. Check items you removed from the box. You should Copyright © 2003 Redline Tuning LLC. All Rights Reserved.
(more…)

[Read more →]

DO NOT try to run the vehicle at full throttle at sea level altitude with a supercharger unless the fuel tank is filled with good 91-octane fuel. Failure to heed this warning can result in severe engine damage. Special Note: If you do not have a factory workshop manual, buy one now! It is good to have for any repairs now and in the future. The factory manual is available from Helm Publications, 800-782-4356. Tools Needed: 8, 10, 11 (7/16”), 12, 13 (1/2”), 14 (9/16”), 15, 17, sockets and wrenches, a 5mm Allen wrench, Phillips and straight blade screwdrivers, and a telescoping magnet.
(more…)

[Read more →]

The Focus Midget engine is equipped with an opposite rotation water pump impeller, and the water pump pulley turns in the opposite direction when compared to the street version of the engine. This does not reverse the coolant flow through the engine, it simply allows the pulley to be driven with the HTD belt instead of using the back-side of a serpentine belt. No modifications to the water pump impeller or water pump pulley are allowed.
(more…)

[Read more →]