Automotive Manual PDF

Read All Instructions Before Beginning Installation
• Installation of a PRO-KIT Spring set should only be performed by a qualified mechanic experienced in the installation and removal of suspension springs.
• Use of a hoist is highly recommended and will substantially reduce installation time.
• Never work on or under a vehicle unless it is properly supported by safety stands and wheels are blocked.
• PRO-KIT Springs are marked with 01 and 02 (located at the end of the part number) designating front and rear spring respectively.
(more…)

[Read more →]

1. Disconnect negative battery cable. PLEASE READ #22 ON THE BACK PAGE!! Push the green plastic tabs, and remove breather hose from vehicle. (Save for later use).
2. Loosen the intake tube hose clamp on the throttle body. Slide the red tab on the electrical connector, and disconnect the mass air sensor.
3. With a 10mm socket, remove the bolt holding the factory airbox to the fender, and save it for re-installation in step #8.
4. Remove the complete factory intake. Use caution to retain the factory grommets in the inner fender.
(more…)

[Read more →]

Before beginning installation, familiarize your-self with the installation instructions and the ultrasonic parking assist system components.
To ensure your safety:
A) Make sure your vehicle is in “PARK”.
B) Apply the emergency brake.
C) Read this manual before starting.

CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting.
(more…)

[Read more →]

1. Start by disconnecting the wire harness from the MAF sensor as shown.
2. Next loosen the hose clamp on the stock air tube to the air box as shown.
3. Remove the stock air tube from the stock air box as shown.
4. Remove the bolt that holds the stock air box in place and set aside for reuse with the MAC system.
5. Remove the stock air box by pulling it straight up as shown.
(more…)

[Read more →]

You have chosen a product that was born from the belief auto accessories should adhere to a higher standard. Assembled by hand in the USA, this pillar will give you the satisfaction of owning a custom part instead of the same old thing. The installation of this part should be an enjoyable task, and may be accomplished with minimal mechanical knowledge and basic hand tools. The instructions will differ slightly from coupe to convertible, as the parts attach to the car in a different manner. These differences are clearly noted for your convenience.
(more…)

[Read more →]

Congratulations, you have just purchased an extremely high quality, high performance kit that introduces you to the world of nitrous oxide. It is imperative that you read and completely understand all aspects of these instructions prior to the installation of your new system. Now, let’s start with a brief look into the basics of nitrous.
(more…)

[Read more →]

Start by disconnecting the wire harness from the MAF sensor as shown.
Next loosen the hose clamp on the stock air tube to the air box as shown.
Remove the stock air tube from the stock air box as shown.
Remove the bolt that holds the stock air box in place and set aside for reuse with the MAC system.
Remove the stock air box by pulling it straight up as shown.
Remove the two rubber grommets from the air box as shown and reinstall them into the stock location.
(more…)

[Read more →]

Study these instructions completely before proceeding. Engine and/or turbocharger damage may occur if any component within these instructions is improperly installed. Turbonetics, Inc or any of its distributors cannot be held responsible for damages as a result of negligent or improper installation. This complete turbocharger system can be installed using common tools and automotive procedures, but installer must have a thorough knowledge of automotive engine operation and feel comfortable working on the vehicle.
(more…)

[Read more →]

1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner assembly.
3. Remove (2) 8mm bolts from throttle linkage bracket and save. (Ref. D)
4. Remove (4) bolts from the throttle body. (Ref. C)
(more…)

[Read more →]

Install
Windshield:
Please check all components in Figures 1 and 2 before assembly.
Align windshield tabs with three holes in Mustang hood and place windshield in position.
Secure windshield by placing three lock washers on windshield tabs on underside of hood
(more…)

[Read more →]