Automotive Manual PDF

1. Remove the OEM gas cap.
2. Remove the 3 mounting bolts from the filler neck.
3. Remove plastic gas shroud by turning counter clock wise and pulling up.
4. Attach the black latch using the 6-32 x 3/16 pan head screws provided.
(more…)

[Read more →]

Installation of performance parts requires good mechanical ability and a complete understanding of the entire machine. The instructions we provide are guidelines only and will not thoroughly explain how to set up a racing vehicle. Claims of performance gains, durability, etc. are based on the experience of TEAM Industries and others and do not constitute a guarantee of similar performance in every application. We believe that the contents and specifications within this set of instructions are correct. We assume no liability for any errors in model applications. We reserve the right to change specifications, product descriptions, product quality and application at any time without notice.
(more…)

[Read more →]

For breaker points, the 5 ohm coils should be used or the 3 ohm coils can be used and a 1 to 2 ohm ballast resistor placed in the 12 volt line going to the coils. Generally, a ballast resistor should not be used with DYNA COILS on electronic ignitions. The secondary towers are designed to accept 7 or 8 mm automotive spark plug wire. Wire kits are available trom DYNATEK.
1) Remove the gas tank. Locate the two ignition coils.
2) Unplug the primary wires coming from the coils and disconnect the high voltage wires from the spark plugs. Remove the coil mounting bolts, and remove the coils.
(more…)

[Read more →]

These instructions explain the procedure required to mount either the Windjammer IV or Vindicator II fairing to your motorcycle. We urge you to follow the preparation and assembly sequence from start to finish. This will benefit you directly in several ways:
1) You will be assured the fairing is properly installed and is immediately ready for operation.
2) You will minimize unnecessary confusion, moaning and scraped knuckles.
3) You will protect your investment by doing it right, and
4) With the confidence that nothing has been overlooked, you won’t have to waste time backtracking to correct mistakes. That’s time you could spend riding.
(more…)

[Read more →]

Congratulations on your purchase of the Honda 750 Ace & Spirit Thunder Air Filter Kit. We’re sure you’ll be pleased with the new level of performance you’ll experience. This kit should be installed on bikes with After Market Exhaust Pipes only and jetted, (jet kit not included). We recommend that an experienced mechanic perform this conversion. Use the appropriate Honda service manual for reference to complete jetting of carbs. Remember, gasoline is extremely flammable and can be explosive under certain conditions. Work in a well-ventilated area and clean up any spills immediately. Check for leaks before riding.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list. Read and understand instructions completely before beginning installation.
STEP 2. Position and hold template on passenger side for square bracket as shown (See Figure 1). (FOR TOYOTA, NISSAN, CHEVY S-10, GMC up to ‘94, and MAZDA up to ‘94 Use template for “L” bracket as shown in Figure 4). Using a center punch, punch each hole. NOTE: If the truck has a bed liner, center punch the bed liner. DO NOT CUT THE BED LINER! Repeat for driver side.
STEP 3. Verify hole locations before drilling (See Figure 2). Drill mounting holes for square brackets using 9/64” drill bit (See Figure 2). For “L” bracket mounting, drill mounting holes using 7/32” drill bit (See Figure 4). Repeat for driver side.
(more…)

[Read more →]

This product is designed to enhance the appearance of the vehicle and to shield the occupants from ordinary weather conditions. Do not rely in any way on the components of this product to contain occupants within the vehicle, or to protect against injury or death in the event of an accident. Never operate vehicle in excess of manufacturer’s specifications.
(more…)

[Read more →]

Remove all parts from you dash, except Speedo trim ring. Install ( 10 ) 8/32 x 5/8 studs in dash adapter as shown in Photo #1.
Install ( 2 ) Gauges in dash adapter as shown in Photo #2.
Install dash adapter as shown in Photo #3
From rear of dash.
Using ( 2 ) 10/32 x 3/8 Pan Head Screws & Washers.
Install the 2 outside gauges as shown in photo #4 & #5.
Do Not Over Tighten Gauges to Panel. Overtightening may break the glass. Leave Clear Protective Covering On Your Panel Until It Is Com- pletely Installed, To Protect The Highly Polished Surface.
(more…)

[Read more →]

Repositions the stock handlebars 1” (25mm) closer to the rider from their tallest adjusted position. No height adjustments are possible with the HR adapter as it maintains the tallest bar position. Heli Bars are designed to safely increase your riding comfort, however it is imperative that these instructions be followed to ensure correct installation. Failure to follow these instructions could result in improper installation and create a dangerous control situation.
(more…)

[Read more →]

Dividers and housings for all tools ? Folding shelves and panels ? Centralized security locking of the two drawer chests ? Flush-fitting side handles ? Oil-proof rubber wheels, 100 mm diam., two fixed and two swivelling, one of which with brake (front wheels on telescopic sliders for greater stability) ? Sheet steel casing, cataphoretic proceeding ? Overall dimensions: closed 650×1000×400 mm open 1300×1400×460 mm  89 Kg Special tool assortment for car repair (334 pcs.) Tool assortment for car repair (203 pcs.) Pcs. Pcs. description Lock ring plier Lock ring plier Lock ring plier
(more…)

[Read more →]