Automotive Manual PDF

RSS Feed

The Resources for Automotive

My 1996 BMW 750iL leaked fuel once. I believe it is the fuel filler hose that is leaking?

December 20th, 2010 · No Comments

How can I access the fuel filler hose and replace it, in order to solve this problem? Can someone show me a diagram or offer detailed instructions? Any help will do.
(more…)

[Read more →]

2003-2005 Hyundai Tiburon V6 Short Ram System Instructions

March 24th, 2010 · No Comments

Removal of the stock intake system.
a. Remove the upper plastic cover covering the stock intake system.
b. Remove the hose clamp securing the upper filter box to the air flow sensor. Unlatch the two clips securing the upper filter box and remove.
c. Remove the filter. Remove the three bolts securing the lower filter box and remove from vehicle.
d. Kit removed from vehicle.
(more…)

[Read more →]

2010 Hyundai Genesis Coupe L4-2.0L Turbo AEM Dryflow Filter Installation Instructions

March 24th, 2010 · No Comments

1. Preparing Vehicle
a. Make sure vehicle is parked on level surface.
b. Set parking brake.
c. If engine has run in the past two hours, let it cool down.
d. Disconnect negative battery terminal.
e. Jack up the front of the vehicle and support using properly rated jack stands.
f. Do not discard stock components after removal of the factory system.
(more…)

[Read more →]

1997-2001 Hyundai Tiburon Cold Air System Installation Instructions

March 10th, 2010 · No Comments

The AEM Cold Air Systems are 50 states Street Legal (some model and years still pending) and come with complete instructions for ease of installation. Our system is constructed of lightweight aluminum and then painted with a zirconia based powder coat for superior heat insulating characteristics. The aluminum will not crack in extended use like plastic and it is actually lighter than plastic. The tube diameter and length are matched for each engine to give power over a broad rpm range. Unlike the plastic systems that use a continually diverging cross section, we take advantage of the acoustical energy in the duct to promote cylinder filling during the intake valve-opening event.
(more…)

[Read more →]

2003-2006 Hummer H2 6.0L V8 Part #3060 Installation Instructions

January 27th, 2010 · No Comments

1. Start by unplugging the MAF sensor by using a screw driver to remove the clip as shown.
2. Push fitting in and pull up to remove the wire harness from the MAF sensor.
3. Remove the bolts that hold the stock air box in place as shown and set aside for reuse with the MAC system.
4. Unbolt the engine cover by using a 10mm socket as shown and set the hardware aside for reuse.
5. Remove the cover to gain access to the hose clamp at the throttle body as shown.
6. Loosen the hose clamp on the stock air tube that attaches at the throttle body as shown.
(more…)

[Read more →]

2003-07 Hummer H2 V8-6.0L K&N Kit Installation Instructions

January 27th, 2010 · No Comments

1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
3. Disconnect the mass air sensor electrical connection.
2. Remove the 8mm bolt that retains then engine cover onto the engine then remove the cover from vehicle.
4. Loosen the hose clamp at the throttle body.
5. Loosen the hose clamp at the mass air sensor.
6. Detach the intake tube from the throttle body and mass air sensor then remove the intake assembly.
NOTE: K&N recommends that customers do not discard factory air intake.
(more…)

[Read more →]

93-97 Honda Accord SOHC, DOHC, VTEC, Non-VTEC, 2.2L PowerAir Throttle Body Spacer

November 18th, 2009 · No Comments

1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Disconnect electrical connectors to throttle body & factory intake tube. See Fig#1
3. Using a 10mm socket, remove two bolts holding throttle cable bracket to intake manifold. Retain bolts for later use. See Fig#2
4. Remove throttle cable(s) from throttle body.
5. Using a Phillips screwdriver, loosen hose clamp on factory intake tube & remove tube from throttle body & air box. See Fig#3
(more…)

[Read more →]

Honda Aero 750 Cruzer Exhaust System

November 16th, 2009 · No Comments

STOCK EXHAUST SYSTEM REMOVAL
1. Remove frame cover.
2. Remove right side footpeg assembly held in place by two bolts (Figure 1).
3. Remove exhaust port nuts.
4. Remove bolts securing rear muffler to exhaust system mounting bracket.
5. Remove complete exhaust system. Begin by lifting muffler out of mounting bracket locating hole (assistance may be required).
6. Check condition of stock exhaust gaskets. Replace if damaged or worn.
7. Remove two bolts attaching stock exhaust mounting bracket to frame.
(more…)

[Read more →]

2006-2007 Honda Civic DX/LX/EX 1.8L Cold Air System Installation Instructions

November 10th, 2009 · No Comments

Removing the stock air inlet system
a) Pry loose the retaining buttons on the lower splash shield.
b) Remove all retaining buttons on the fender liner around the fender well.
c) Carefully pull back the fender liner and splash shield to gain access to the fender well and stock resonator box.
d) Remove the battery from the engine bay.
e) Remove the plastic battery tray.
(more…)

[Read more →]

2004-05 Honda Civic L4-1.6L Typhoon Cold Air Intake System Installation Instructions

November 5th, 2009 · No Comments

TO START:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the air temperature sensor electrical connection as shown.
3. Unclip the battery cable from the air inlet duct as shown.
4. Loosen and remove the two bolts that secure the air inlet duct as shown.
5. Remove the air inlet duct.
6. Loosen and remove the four bolts that secure the air intake resonator.
(more…)

[Read more →]