Automotive Manual PDF

RSS Feed

The Resources for Automotive

2003-07 Hummer H2 V8-6.0L K&N Kit Installation Instructions

January 27th, 2010 · No Comments

1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
3. Disconnect the mass air sensor electrical connection.
2. Remove the 8mm bolt that retains then engine cover onto the engine then remove the cover from vehicle.
4. Loosen the hose clamp at the throttle body.
5. Loosen the hose clamp at the mass air sensor.
6. Detach the intake tube from the throttle body and mass air sensor then remove the intake assembly.
NOTE: K&N recommends that customers do not discard factory air intake.
(more…)

[Read more →]

93-97 Honda Accord SOHC, DOHC, VTEC, Non-VTEC, 2.2L PowerAir Throttle Body Spacer

November 18th, 2009 · No Comments

1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Disconnect electrical connectors to throttle body & factory intake tube. See Fig#1
3. Using a 10mm socket, remove two bolts holding throttle cable bracket to intake manifold. Retain bolts for later use. See Fig#2
4. Remove throttle cable(s) from throttle body.
5. Using a Phillips screwdriver, loosen hose clamp on factory intake tube & remove tube from throttle body & air box. See Fig#3
(more…)

[Read more →]

1998-2002 Honda Accord 4 Cyl. Cold Air System Installation Instructions

November 17th, 2009 · No Comments

Read and understand these instructions BEFORE attempting to install this product.
1. Make sure vehicle is parked on a level surface.
2. Set parking brake.
3. Disconnect negative battery terminal.
4. If engine has run within the past two hours let it cool down.
5. The following items will be removed from the vehicle.
(a) The OE inlet tube
(b) The air filter case
(c) Intake air noise resonators (Fig A)
(more…)

[Read more →]

00-Up Honda S2000 Cold Air Intake Installation Guide

November 1st, 2009 · No Comments

Removal of Factory Intake
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Unclip the six over center clamps, then remove the air cleaner lid.
3. Remove the air injection pump hose from the stock intake tube.
4. Remove the crank case vent hose from the stock intake tube.
5. Loosen the hose clamp at the throttle body, then remove the intake tube and filter.
6. Remove the solenoid from the lower air cleaner assembly.
7. Unclip the wire harness from the lower air cleaner assembly.
8. Unclip the vacuum hose from the rear of the lower air cleaner assembly.
9. Remove the three bolts that secure the lower air cleaner assembly.
10. Remove the lower air cleaner assembly.
11. Remove the stock rubber hose from the crank case vent on the cam cover and from the hard line.
(more…)

[Read more →]

2003-2004 Honda Accord 4-Cyl. 2.4L Short Ram Intake System Installation

October 28th, 2009 · No Comments

Removal of the Stock Air Intake System
a) Loosen the clamp around the throttle body using a 5.5mm socket or screwdriver. Pull the Intake Air Temperature (IAT) sensor out of the intake tube by loosening the spring loaded clamp.
b) Unplug the breather tube from the fitting underneath the intake manifold.
c) Remove the air box mounting bolt shown in the picture.
d) Remove the other air box mounting shown in the picture.
e) Carefully remove the air box assembly from the engine bay.
f) Remove the two fasteners holding the plastic cover in front of the battery.
(more…)

[Read more →]

99-05 Chevy/GMC PU/SUV 4.8, 5.3, 6.0L Airaid Modular Intake Tube Installation Instructions

October 22nd, 2009 · No Comments

Installation Instructions. Read Me!
I. DISCONNECT NEGATIVE (-) BATTERY CABLE
II. Remove Factory Intake Assembly
a) Loosen the factory hose clamps on each end of the factory intake tube assembly.
b) Using a flat head screwdriver, gently pry the radiator hose bracket from the factory intake tube assembly and remove from vehicle.
(more…)

[Read more →]

2004 Chevy HD Truck Duramax Diesel High Output “LLY” Installation Instructions

October 12th, 2009 · No Comments

Tools Required For Installation:
Flat Head Screwdriver
8mm, 10mm Socket
Ratchet & Extension
3/32”, 5/32” Allen Wrench
#T20 Security bit (Included)
1. Disconnect the negative battery cable. Disconnect the Mass Air Flow (MAF) sensor wiring harness. Using the supplied T-20 Security bit, remove the two screws and the Mass Air Flow sensor from the tube (save the sensor for reuse). Loosen the hose clamps on each end of the factory intake tube assembly.
(more…)

[Read more →]

2002 Chevy Trailblazer / GMC Envoy Air Intake Installation Instructions

October 6th, 2009 · No Comments

These instructions will take you through the installation of your new air intake system for your vehicle. We always recommend that you keep your stock air intake system in storage in case you might need it later.
Kit includes: air filter, air intake tube, bracket, (2) 3” hose clamps, red connecting hose and rubber grommet.
Tools required: Phillips head screwdriver and 5/16” nut driver.
(more…)

[Read more →]

2007-2008 Chevy 4.8, 5.3, 6.0 Silverado/Sierra VPI Cold Air Performance Intake System Installation

October 4th, 2009 · No Comments

Installation Instructions:
1. Disconnect negative battery cable. Then loosen all three factory hose clamps located at the Mass Air Flow (MAF) meter and both factory intake tube.
2. Remove black cover on throttle body by pulling up and sliding towards front of truck. It is held by two grommets. Gently pry the radiator hose bracket from the factory intake tube assembly and remove the tube from the vehicle. A flat head screwdriver may be used.
3. Remove the factory air filter base and lid as an assembly. There are no bolts, just friction mounts, so just pull straight up on the air filter base to remove. Then remove the plate that held the base and lid. There are (5) 10mm bolts to unscrew to remove the plate. After everything is removed it should look like the picture above.
(more…)

[Read more →]

1996-00 Chevrolet, GMC Truck & SUV 5.7L V-8 ECONOAID Throttle Body Plate Instructions

October 4th, 2009 · No Comments

1. Disconnect the negative battery cable! Remove the plastic wing nut on the air intake hat behind the throttlebody. Loosen the hose clamp that secures the flexible intake tube to the throttle body hat. Disconnect the crankcase breather hose. Roll the air intake hat towards the front of the vehicle to remove it, and set it aside.
2. A.) Remove the three bolts that secure the throttlebody to the intake manifold. B.) Remove the bolt that secures the throttle cable bracket to the throttlebody. C.) Lift up the tabs, and disconnect the two wiring harnesses of the drivers side of the throttlebody. Lift the throttlebody off of the intake manifold and set it to the side.
(more…)

[Read more →]