Automotive Manual PDF

RSS Feed

The Resources for Automotive

1991-1994 FORD TEMPO VEHICLE WIRING

August 4th, 2010 · No Comments

WIRING INFORMATION: 1991 Ford Tempo WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition harness STARTER WIRE WHITE/PINK Ignition harness 12V IGNITION WIRE RED/LT.GREEN Ignition harness ACCESSORY WIRE GRAY/YELLOW Ignition harness POWER DOOR LOCK (5-wire reverse PINK/YELLOW Harness In Driver’s Kick Panel polarity POWER DOOR UNLOCK (5-wire reverse PINK/GREEN Harness In Driver’s Kick Panel polarity PARKING LIGHTS (+) BROWN At Headlight Switch Or Harness In Driver’s Kick Panel DOOR TRIGGER (+) BLACK/BLUE At Courtesy Light Under Dash TRUNK RELEASE (+) PURPLE/YELLOW At Trunk Release Switch TACHOMETER WIRE TAN/YELLOW At Ignition Coil (more…)

[Read more →]

2006-09 Honda S2000 Base, High-Boost, and YouTune Supercharger Kits Installation

November 18th, 2009 · No Comments

SECTION 1: PRE-INSTALLATION PRECAUTIONS:
Step 1: Remove the negative battery cable. Before removing the battery cable, verify that you have the “anti theft” radio code. It is usually located in your owner’s manual. If you cannot find the radio code, take your car to your local Honda dealer so that they can retrieve the code through the Honda computer network.
Step 2: Jack your car up, or put the car up in the air if you are working in a shop. Support your car with Jack Stands or Ramps if you are working on the ground. Never work under a car without some type of reliable support.
(more…)

[Read more →]

Kodiak Kits Installation Instructions

September 13th, 2009 · No Comments

Step Installation: Complete Part One, then find the section for specific instructions for your model vehicle.
Part One: Rear bracket attachment
Step 1) Attach the rear brackets to the step as shown in Figure 1, using a washer, E, and nut, I, on each stud. Tighten each nut.
Step 2) Place the cross member in position as shown in Figure 2, and secure using washers D and F, and one nut, H on each stud. Leave fasteners loose, as the bracket slots will be used to determine exact fit of rear upright bracket.
(more…)

[Read more →]

Ford EEC-V J3-8B Chip module Install Instructions

July 23rd, 2009 · No Comments

When working with static sensitive electronic parts, care must be taken to ensure the electronics are not damaged from static electricity discharge. You can wear a static strap grounded to the vehicles body as the safest way to guard against static discharge. Alternatively you can touch a raw metal (unpainted) part of the body to ground yourself and discharge any static buildup. Do this regularly to prevent static build up.
(more…)

[Read more →]

87-91 Ford Bronco Installation Instructions

May 29th, 2009 · No Comments

1 Read instructions completely and carefully before you begin. Checkthekitfor proper contents (refer to parts list and picture diagrams).
2. Park the vehicle on a clean, dry flat (level) surface. Block the tires so the vehicle cannot roll in either direction. Automatic transmissions should be placed in neutral.
3. Remove both battery cables. Be sure to disconnect the negative cable first, then the positive cable.
(more…)

[Read more →]

2006 Ford Fusion Quick Reference Guide

April 29th, 2009 · No Comments

Your fuel tank can accommodate approximately 17.5 gallons (66.2 L) of gasoline. Your vehicle is designed to use unleaded gasoline with an (R+M)/2 octane rating of 87. Using gasoline with a lower octane rating may degrade performance.
(more…)

[Read more →]

Ford Focus Dead Pedal Installation Guide pdf

March 27th, 2008 · No Comments

Please gather the following tools before you begin the installation: * Power Drill. * 3/16 drill bit. * Large flat head screw driver. * Large Phillips head screw driver. * Sharp utility knife or razor blade. * Fine permanent marker. * Center punch & hammer – optional. Step 2 – Unpack Dead Pedal kit and verify contents. Remove all items from the the shipped package. Copyright © 2003 Redline Tuning LLC. All Rights Reserved. You should have the following before beginning: * RedlineTuning Focus Dead Pedal * (2) Washers * (2) Sheet Metal Screws * Printed Installation Instructions
(more…)

[Read more →]