Automotive Manual PDF

The rack must be inspected before each use to make certain attachments are secure, and for evidence of Wear. Misuse of the rackor failure to observe the manufacit/rer ’s mär action s as to installation, proper Attachment and maintenance will void any warranties that may be implied by law.
1. Plastic Bag labeled #1 remove contents and press rubber protective strip #1 on to bottom of fairing #2.
2. Plastic Bag, labeled #2 re move c ontents and place black button head sere w #3 thru blac k washe r and then thru fairing #2. Place fairing onto bracket #4 and attach black washer, lock washer and wing nut finger tight only. Attach all 4brackets but do not attach fairing to rack at this time.
(more…)

[Read more →]

Installation Instructions
1. After bike is cool make sure the bike is secured before beginning the installation.
2. Remove the right side fairing (refer to the owners manual for more information on removal).
3. Remove the stock exhaust from the bike. Unbolt the exhaust mount on the rear peg and loosen the collector clamp and remove the stock system.
4. Attach the LOR exhaust canister to the slip-on tube adapter with the spring tabs aligned (make sure your hands are protected with a pair of gloves in case the tubes slip). You may have to squeeze the mid-pipe adapter tube to fit into the exhaust inlet as the mandrel bends may become slightly out of round due to a cut near the bend (the tube will take form once connected). Slide the canister all the way until the slip-on adapter seats fully against the exhaust inlet. Wipe off any excess silicone.
(more…)

[Read more →]

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Determine driver and passenger Mounting Brackets.
3. Hang the inner side of the driver front Mounting Bracket into position by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame (Figure 1). NOTE: There are two threaded holes by the front mounting location on the frame, use the one towards the rear of vehicle.
4. Attach the opposite side of the driver front Mounting Bracket to the threaded holes on the floor panel of the vehicle by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers (Figure 1).
5. Locate and cut out the openings in the driver and passenger side trimming templates with a pair of scissors (Page 3 & 4)
6. Fit the driver’s side template onto its respective side plastic rock shields. Position them using two each of the 8mm bolts that will later be used to mount the side bar brackets. Transfer the openings in the templates onto the plastic cover using a magic marker.
7. Now remove the rock shield from the undercarriage of the car. The three front screws can be removed with a 10MM socket. The plastic retainer plugs can be removed with a flat blade screwdriver.
8. Using a sharp knife or pair of shears, cut out the shields as marked using the templates (Figure 2).
9. Insert the inner side of driver rear Mounting Bracket through previously cut out hole on the plastic cover. Hang Mounting Bracket by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame (Figure 3). NOTE: There are two threaded holes on the frame, use the one towards the rear of vehicle.
10. Attach the opposite side on the driver rear Mounting Bracket by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers into factory threaded holes on the floor panel.
11. Position Driver Side Bar onto Mounting Brackets. Attach Side Bar to Mounting Brackets using the included (4) 8mm x 30mm Hex Head Bolts, (4) 8mm Lock Washers, and (4) 8mm Flat Washers (Figure 1). Do not tighten at this time.
12. Level and adjust Side Bar; then tighten all hardware at this time.
13. Re-install the rest of fastener on the rock shield.
14. Repeat steps 2-13 for passenger Side Bar.
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Get pdf

[Read more →]

All left / right descriptions are from the point of view of the rider when seated on the bike in the riding position.
Note: the condenser upgrade cable supplied will have a black cover to make it inconspicuous enough for a concours show bike. The example shown has a red cover to highlight the correct location and routing.
1. Place the bike on the center stand.
2. Remove the left side cover.
3. Loosen the rear engine mounting bolt. This is a long bolt that passes through both rear engine hangers. If mounted correctly, the nut, washer and lock washer should be on the right side of the bike. Yours may be reversed.
(more…)

[Read more →]

1. Remove contents and check for damage. Verify all parts are present. Read instructions completely before installation.
2. Locate driver side mounting locations on vehicle (See Figure 1and 2). Repeat for passenger side.
3. Attach driver side front and rear mounting brackets to underside of rocker panel as shown using M8 hex bolts, 5/16” flat washer and 5/16” lock washer. Hand tighten only (See Figure 1 and 2). Repeat for passenger side.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
STEP 2. Read and understand instructions completely before beginning installation.
STEP 3. Determine passenger and driver mount brackets from figure above.
STEP 4. Remove the (16) push type retainers and (2) 6mm bolts from the lower splash shield. Remove plastic splash shield to gain access to mounting locations.
STEP 5. Locate the (4) 14mm holes in the lower radiator support. Attach the mount brackets using the (4) 1/2-13 x 1.00” hex head bolts, (4) 1/2” external-internal tooth lock washer, (4) 1/2” flat washer, (4) 1/2” lock washer, (4) 1/2-14 hex nuts, (2) 5/16-18 x 1.75” hex head bolts, (2) 5/16” lock washer, (2) 5/16” flat washers and (2) 5/16-18 flange lock nuts. Leave loose.
CAUTION: Wheels must be supported to support sub-frame to the unibody to avoid misalignment for re- attachment.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
STEP 2. Read and understand instructions completely before beginning installation.
STEP 3. Determine passenger and driver brackets. SEE FIGURE 1.
STEP 4. Remove (16) push type retainers from lower splash shield. Remove plastic splash shield to gain access to mounting locations.
STEP 5. Locate bolts that hold the frame brace and bumper brackets to vehicle. Remove bolts using a 17mm and 14mm socket and ratchet.
STEP 6. Install bracket between lower radiator support and frame brace using (2) 1/2” flat washers on top of bracket’s frame brace slots and replace bolts. Install (1) 3/8-16 x 1.00” hex head bolt, (1) 3/8” lock washer and (2) 3/8” flat washers. Leave loose. SEE FIGURE 1. NOTE: It may necessary to loosen body mount bolt holding the frame brace to gain enough clearance to slide brackets in place.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
STEP 2. Read and understand instructions completely before beginning installation.
STEP 3. Determine Driver and Passenger Uprights and Top and Bottom Tubes. (Uprights are positioned so raised side of bolt holes are facing each other and the Tube with the two pierced holes is the Bottom Tube).
(more…)

[Read more →]

Remove the contents from the box and check for any damage. Verify all parts against the parts list.
Read and understand instructions completely before beginning installation.
Remove 10mm bolts from bumper brace located on back side of front body mount if present. For each side, place Mount Bracket up to the backside of the body mount and secure using existing 10mm bolts removed in step 3. (On trucks without existing bolts, use the 10mm hardware provided in the bolt kit).
(more…)

[Read more →]

Apply for below vehicle:
2000-2007 Chevy Silverado 1500 Crew Cab
2000-2007 GMC Sierra 1500 Crew Cab
2001-2007 Chevy Silverado HD Crew Cab
2001-2007 GMC Sierra HD Crew Cab

2006 and newer General Motors trucks have a larger cab mount bolt than in previous years. You will need to reuse your factory cab mount bolts when installing this kit on those trucks.
(more…)

[Read more →]