Automotive Manual PDF

Step 1
Remove the driver’s side hood cover by prying upward with both hands.
Step 2
Remove the driver’s side windshield molding. Do not peel off the rubber seal or separate from roof molding.
Step 3
Remove 4 screws from driver’s side roof railing. Remove roof and windshield molding and set it down on the table.
Step 4
Measure 1” from the beginning of the roof railing and mark on the masking tape the spot to drill ―” hole for your harness.
(more…)

[Read more →]

INSTALLATION:
1. POSITION RACK SQUARELY ON TRUNK LID AS FAR FORWARD AS POSSIBLE WITHOUT ALLOWING ENDS TO RUB ON PASSENGER BACKREST SECTION.
2. LIFT RACK SLIGHTLY AND PLACE THREE 3″ - 4″ PIECES OF MASKING TAPE UNDER EACH OF THE REAR LEGS. (FIG B).
3. USE A MARKING PEN TO OUTLINE EACH OF THE FOUR MOUNTING LEGS ONTO THE TAPE STRIPS.
4. REPOSITION THE RACK OVER THE MARKED CIRCLES TO MAKE CERTAIN THE RACK IS IN THE EXACT LOCATION YOU DESIRE. (IF NECESSARY, REMARK ANY INCORRECT CIRCLE MARKINGS.)
(more…)

[Read more →]

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.

NOTE:
• Be careful not to damage the body paint finish.
• Body side moldings should only be installed if the ambient air temperature is 15°C (60°F) or above.
• To allow the adhesive to cure, do not wash the vehicle for 24 hours. Please advise the customer.
• These installation instructions show the left body side moldings being installed. The same procedure applies to installing the right body side moldings.
(more…)

[Read more →]

1. Attach the left strake to the side under spoiler using the three self-tapping screws.
2. Remove the three self-tapping screws that fasten the front inner fender to the fenderwell.
3. Remove the four clips that fasten the existing side under spoiler to the side sill, then remove the spoiler by sliding it toward the front.
4. Remove the spring nut from the end of the side under spoiler you just removed.
5. Remove the eight clips from the side sill by turning them 45 degrees.
(more…)

[Read more →]

INSTALLATION NOTE:
• These instructions are for the left door visors, the same procedure applies to the right door visors.
• Be careful not to damage the glass run channels and body finish.
• The door visors are not designed to absorb shock or impact. To prevent damage, handle with care.
• This door visor kit should only be installed if the ambient air temperature is 60°F (15°C) or above.
• To allow the adhesive to “cure,” do not wash the vehicle for 24 hours.
• Follow the instructions shown on the caution label attached to the container before applying the primer.
(more…)

[Read more →]

PROCEDURE:
1. Remove push type retainers from lower splash shield. Remove plastic splash shield to access to mounting location.
2. Locate and remove bolts that hold the frame brace and bumper brackets to vehicle.
3. Install frame bracket between lower radiator support and frame brace using (3) existing bolts. As shown.
4. Cut plastic splash shield to allow brackets to pass through. See Cutting Instruction sheet for guidelines on cutting. Reinstall plastic splash shield over brackets in this same order removed.
(more…)

[Read more →]

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE: These installation instruction show the left fog light begin installed. The same procedure applies to installing the right fog light.
(more…)

[Read more →]

The badges are made from layers of foil and other materials, all covered with a pliable urethane clear “lens.” They are thin, not more than 1/16 inch thick, so they are very slick and appear to have been molded right into the painted surface of the body work. In comparison, the raised stock badges and aftermarket versions look rather crude. Since the badge colors match the various car colors perfectly, the integrated appearance of the badges is all the more striking. Depending on the color of your car and the color of the badge you chose, the end result could be very subtle and sophisticated or more striking. To avoid mistakes, please read these directions fully before beginning.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
STEP 2. Read and understand instructions completely before beginning installation.
STEP 3. Determine passenger and driver brackets. SEE FIGURE 1.
STEP 4. Remove (16) push type retainers from lower splash shield. Remove plastic splash shield to gain access to mounting locations.
STEP 5. Locate bolts that hold the frame brace and bumper brackets to vehicle. Remove bolts using a 17mm and 14mm socket and ratchet.
STEP 6. Install bracket between lower radiator support and frame brace using (2) 1/2” flat washers on top of bracket’s frame brace slots and replace bolts. Install (1) 3/8-16 x 1.00” hex head bolt, (1) 3/8” lock washer and (2) 3/8” flat washers. Leave loose. SEE FIGURE 1. NOTE: It may necessary to loosen body mount bolt holding the frame brace to gain enough clearance to slide brackets in place.
(more…)

[Read more →]

1. Read and understand these instructions before proceeding. If you drop a screw down in some stake pocket holes it is difficult to retrieve. Some installers prefer to apply masking tape around the stake pocket holes to prevent scratches. Remove the tape before tightening the assembly screws.
2. Select the correct stake pocket insert. The flat model is used for the 88-98 Chevy & GMC models. All other trucks use the insert with the bent flanges. The bent flange style should be oriented with the bent wings pointing up like this: [__________]
(more…)

[Read more →]