Automotive Manual PDF

Please take a few moments to review this manual thoroughly before you begin work: A quick parts check to make certain your kit is complete (See shipper parts list in this package). If you discover shipping damage or shortage, please call our office immediately. Take a look at exactly what you are going to need in terms of tools, time, and experience. Review our limited warranty with care. When unpacking the supercharger kit DO NOT lift the supercharger assembly by the black plastic bypass actuator. This is pre-set from the factory and can be altered if used as a lifting point!
(more…)

[Read more →]

Power Plant
Removing the cylinder head
Caution : The manufacturer assumes no responsibility for damage resulting from the use of unsuitable tools for the removal and refitting of the engine or any part of it.
When the engine is in place, the cylinder head, the cylinder, the piston and the reed valve can be exposed by removing the following parts: exhaust pipe, air filter casing, carburettor.
(more…)

[Read more →]

Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay. CAUTION: When battery is disconnected, vehicle computer and memory systems may lose memory data. Driveability problems may exist until computer systems have completed a relearn cycle. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION before disconnecting battery.
(more…)

[Read more →]

Please take a few moments to review this manual thoroughly before you begin work: Μake quick parts check to make certain your kit is complete (see shipper parts list in this package). If you discover shipping damage or shortage, please call our office immediately. Take a look at exactly what you are going to need in terms of tools, time, and experience.
(more…)

[Read more →]

Please take a few moments to review this manual thoroughly before you begin work: Μake quick parts check to make certain your kit is complete (see shipper parts list in this package). If you discover shipping damage or shortage, please call our office immediately. Take a look at exactly what you are going to need in terms of tools, time, and experience. Review our limited warranty with care.
(more…)

[Read more →]

Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay.
VALVE CLEARANCE
NOTE: Adjust valve clearance with engine cold.
NOTE: If valve cover uses grommets below retaining nuts or bolts, keep grommets in order so they are installed in original locations during reassembly.
(more…)

[Read more →]

Relieve the fuel system pressure before servicing fuel system components in order to reduce the risk of fire and personal injury. After relieving the system pressure, a small amount of fuel may be released when servicing the fuel lines or connections. In order to reduce the risk of personal injury, cover the regulator and fuel line fittings with a shop towel before disconnecting. This will catch any fuel that may leak out.
(more…)

[Read more →]

Magna Charger has seen a variance in stock rear wheel horsepower. Numbers between 280 RWHP and 320 RWHP have been recorded on our in-house chassis dynamometer. Depending on year, transmission, or presence of other installed aftermarket products, RWHP numbers of up to approximately 450 at 7 lbs. of boost can be achieved with the installation of the Magna Charger Corvette intercooled supercharger system. Horsepower numbers are reflected by base RWHP numbers and altitude. Magna Charger systems are manufactured to produce about 20 RWHP per pound of boost at sea level. High altitudes will produce different numbers.
(more…)

[Read more →]

Our Magna Charger kits are designed for stock engines, with stock components, in good mechanical condition only. Installation on worn or damaged engines is not recommended and may result in engine failure, for which we naturally can’t be responsible . Magna Charger is not responsible for the engine or consequential damages.
(more…)

[Read more →]

The following diagnostic steps will help prevent overlooking a simple problem. This is also where to begin diagnosis for a no-start condition. The first step in diagnosing any drive ability problem is verifying the customer complaint with a test drive under the conditions the problem reportedly occurred. Before entering self-diagnostics, perform a careful and complete visual inspection. Most engine control problems result from mechanical breakdowns, poor electrical connections or damaged/misrouted vacuum hoses. Before condemning the computerized system, perform each test listed in this article.
(more…)

[Read more →]