Automotive Manual PDF

RSS Feed

The Resources for Automotive

2001 LIGHT TRUCK INCOMPLETE VEHICLE MANUAL

July 19th, 2010 · No Comments

The cover of this manual identifies the four incomplete vehicle configurations for which compliance representations are contained in this manual. Also, a label is affixed to the cover which includes the Vehicle Identification Number (VIN) for the specific vehicle to which this manual belongs. The label identifies the following information which pertains only to the vehicle with the corresponding VIN.
(more…)

[Read more →]

H2 Hummer Low Profile Light Bar Instructions

January 27th, 2010 · No Comments

INSTALLATION:
1. Disconnect negative battery terminal. Remove phillips head screw from driver side marker light lens and remove lens assembly. Pull up the wire boot.
2. Remove driver side assist handle by pulling out locking tabs with a small flat blade screwdriver until they “click”. Next, remove the A-Pillar trim and place on dash.
3. Remove the fuse cover panel on the left side of dash. There are two clips at the top and one at the bottom.
4. Using a 13mm socket, remove 4 bolts, one plastic stud, and remove the driver’s side hood stop bracket for access to the main wire harness boot.
(more…)

[Read more →]

Honda Reflex Windscreen Installation/Removal

October 30th, 2009 · No Comments

Tools/Supplies: Phillips screwdriver, windscreen, maybe glue
Step 1­ Remove the 2 screws just below the “HONDA” decal on the front cowl (just below the windscreen).
Step 2 ­ Remove the 2 screws on the pillars that connect the sides of the windscreen to the scooter (1 screw on each pillar, screw heads face driver)
(more…)

[Read more →]

2003 Chevrolet/GMC 2500HD RECON 3-Piece Cab Roof Light Installation

October 10th, 2009 · No Comments

This document covers the installation of RECON Truck Accessories 3-Piece running lights on a 2003 Chevrolet/GMC Silverado/Sierra 2500 HD. RECON 3-piece Chevy/GMC Cab Roof Light Kit Boasts The Following:
Provides Maximum Visibility
Meets S.A.E. specifications
Adapts to Curved and Flat Roofs
Replaceable 194-Style Bulbs
Kit includes 2 Corner Clearance Lights and 1 Three Lamp Cluster Center Marker Light
Complete Wiring Harness with Quick Wire Connectors
Great Retail-Friendly Packaging
All Necessary Hardware
(more…)

[Read more →]

Ford F-150 Bed Extender Bracket Installation

July 15th, 2009 · No Comments

F-150 QUICK LATCH MOUNTING BRACKET INSTRUCTIONS
Step 1. Remove contents from box and check for damage. Verify all parts against parts list. Read and understand instructions completely before installation.
Step 2. Assemble brackets as shown in Figure 1.
Step 3. With lever towards the tailgate side insert lower hold-down bracket through lower hole on d-pillar.
Step 4. Insert upper hold-down bracket in upper hole of d-pillar.
(more…)

[Read more →]

1994-2004 Ford Mustang A-Pillar Gauge Pods Installation Guide

May 30th, 2009 · No Comments

You have chosen a product that was born from the belief auto accessories should adhere to a higher standard. Assembled by hand in the USA, this pillar will give you the satisfaction of owning a custom part instead of the same old thing. The installation of this part should be an enjoyable task, and may be accomplished with minimal mechanical knowledge and basic hand tools. The instructions will differ slightly from coupe to convertible, as the parts attach to the car in a different manner. These differences are clearly noted for your convenience.
(more…)

[Read more →]

2005-2009 Ford Mustang A-Pillar Rattle Noise

April 7th, 2009 · No Comments

Some 2005-2009 Mustang vehicles may exhibit a rattle noise where the A-pillar meets the dash area. This rattle may be due to worn, missing or off location tape under the dash panel and/or A-pillar dual lock (velcro) fastener(s) not seated.
(more…)

[Read more →]

2001 VW Golf TDI Gauge Installation

August 14th, 2008 · No Comments

This page describes my aftermarket gauge install on my 2001 VW Golf TDI. It should directly apply to any Mk4 (99.5+) Golf or Jetta TDI and it should apply to the 98+ New Beetle TDIs. For other engines, wiring should be similar, but the installation of senders into the engine will be different. The intention of this page is to share information about my install and to help others who are considering an install. I tried to photograph everything important. Shoot me an email if you can think of a photo that you’d like to see that I haven’t included. In fact, any comments are welcome.
(more…)

[Read more →]

Mitsubishi Lancer

June 19th, 2008 · No Comments

Every effort has been made to ensure that the contents of this publication were accurate and up-to-date at the time of going to press. The right is reserved to change specifications, partnumbers and features without prior notice. To avoid any misunderstandings your Mitsubishi Motors dealer will advise of any alterations made since the date of issue of this brochure. No part of this publication may be reproduced in any form or by any means, without the prior written permission of Mitsubishi Motors Europe B.V.. Some of the products or vehicles shown in the brochure may differ from the models available in your market.
(more…)

[Read more →]

2008 MITSUBISHI LANCER GTS Overview

June 19th, 2008 · No Comments

The all-new Lancer is larger in every dimension except length, where it has lost 1.5 centimetres. It rides on a brand-new platform shared with the new Outlander, which provides a 56% increase in torsional rigidity and 50% more bending rigidity. For the time being, the front-drive Lancer is offered as a sedan with a choice of three trim levels: DE, ES and GTS.

In the works for the 2009 model-year are a Ralliart version, a station wagon, and a larger, 2.4-litre engine for the GTS. The very sporty Evolution with 291 horsepower is available for the first time in Canada.
(more…)

[Read more →]