Automotive Manual PDF

SECTION 1: PRE-INSTALLATION PRECAUTIONS:
Step 1: Remove the negative battery cable. Before removing the battery cable, verify that you have the “anti theft” radio code. It is usually located in your owner’s manual. If you cannot find the radio code, take your car to your local Honda dealer so that they can retrieve the code through the Honda computer network.
Step 2: Jack your car up, or put the car up in the air if you are working in a shop. Support your car with Jack Stands or Ramps if you are working on the ground. Never work under a car without some type of reliable support.
(more…)

[Read more →]

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Determine driver and passenger Mounting Brackets.
3. Hang the inner side of the driver front Mounting Bracket into position by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame (Figure 1). NOTE: There are two threaded holes by the front mounting location on the frame, use the one towards the rear of vehicle.
4. Attach the opposite side of the driver front Mounting Bracket to the threaded holes on the floor panel of the vehicle by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers (Figure 1).
5. Locate and cut out the openings in the driver and passenger side trimming templates with a pair of scissors (Page 3 & 4)
6. Fit the driver’s side template onto its respective side plastic rock shields. Position them using two each of the 8mm bolts that will later be used to mount the side bar brackets. Transfer the openings in the templates onto the plastic cover using a magic marker.
7. Now remove the rock shield from the undercarriage of the car. The three front screws can be removed with a 10MM socket. The plastic retainer plugs can be removed with a flat blade screwdriver.
8. Using a sharp knife or pair of shears, cut out the shields as marked using the templates (Figure 2).
9. Insert the inner side of driver rear Mounting Bracket through previously cut out hole on the plastic cover. Hang Mounting Bracket by partially threading (1) 8mm x 30mm Hex Head Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer into factory threaded hole on the frame (Figure 3). NOTE: There are two threaded holes on the frame, use the one towards the rear of vehicle.
10. Attach the opposite side on the driver rear Mounting Bracket by partially threading (2) 8mm x 30mm Hex Head Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers into factory threaded holes on the floor panel.
11. Position Driver Side Bar onto Mounting Brackets. Attach Side Bar to Mounting Brackets using the included (4) 8mm x 30mm Hex Head Bolts, (4) 8mm Lock Washers, and (4) 8mm Flat Washers (Figure 1). Do not tighten at this time.
12. Level and adjust Side Bar; then tighten all hardware at this time.
13. Re-install the rest of fastener on the rock shield.
14. Repeat steps 2-13 for passenger Side Bar.
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Get pdf

[Read more →]

Relieving fuel pressure
a) Remove the fuel fill cap.
b) On models equipped with a 6mm service bolt. (illustrated below) If your vehicle is not equipped with a 6mm service bolt, then proceed to step c.
i) Use a box end wrench on the 6mm service bolt on top of the fuel filter or fuel rail, while holding the special banjo bolt with another wrench.
ii) Place a rag or shop towel over the 6mm service bolt.
iii) Slowly loosen the 6mm service bolt one complete turn.
iv) Leave service bolt loose until all pressure has been relieved.
v) Tighten service bolt to 10 lbf-ft.
(more…)

[Read more →]

Preparation
1. Ensure all lamps and accessories are OFF.
2. Ensure the ignition switch is in the OFF position.
3. Loosen the negative battery cable bolt. Remove negative battery cable from terminal and position away from battery.
4. Wait one (1) minute prior to working on the vehicle to assure SIR roof rail airbag system has been disabled for your safety. Install Camera into Endgate
(more…)

[Read more →]

Adapter plate F-15741-TL29PL is required to hold VW 09G (TF-60SN) and Volvo/Opal (TF-80SC) valve body sections while reaming. Adapter plate is not required for Ford/Mazda (TF-81SC).
Note: Mounting instructions are included with the Adapter plate F-15741-TL29PL. Disassembly Steps
Remove the retainer, plunger sleeve with plunger valve, spring and lock-up valve. Keep the retainer for re-use and discard all other OE pieces.
(more…)

[Read more →]

1. The electrical power to the air suspension system must be turned o prior to hoisting, jacking or towing an air suspension vehicle. Failure to do so can result in unexpected ination or deation of the air springs, which can result in shifting of the vehicle during these operations. Turn the air suspension service switch o.
2. WARNING: Do not remove the center nut. This nut holds the upper spring mount in place and if this nut is removed the spring tension will be released. Failure to follow these instructions may result in personal injury. Remove and discard the nuts.
3. Remove the wheel and tire assembly.
(more…)

[Read more →]

Tensioner
1. Hold Tensioner Body in a vise to remove bolt & washer from tensioner pulley (note; bolt is a left-handed thread, turn clockwise to remove). Discard washer.
2. Place Tensioner Cover Plate (781-A) on Tensioner Body & replace pulley.
3. Mount Tensioner Nose Cover Retainer (780-A) on tensioner pulley & replace bolt.
4. Mount Tensioner Nose Cover (307) to Tensioner Nose Cover Retainer (780-A) using three 8-32 x 5/8” socket head cap screws.
5. Mount Tensioner to Tensioner Base (30019) using one 5/16-18 x 3” socket head cap screw.
6. Mount Tensioner Base (30019) to engine block thru water pump mounting holes using two 5/16-18 x 2 3/4” socket head cap screws & to engine block using one 3/8-16 x 3” socket head cap screw & one Spacer (TP3 1.775), placing Spacer (TP3 1.775) between Tensioner Base (30019) & engine block.
(more…)

[Read more →]

This manual is used for Integrated DVD Rear Seat Entertainment System in to Ford Territory 2004 onwards, Ford BA Falcon 2003 onwards, Ford FG Falcon 2008 onwards.

Step 1
Disconnect cable from the negative battery terminal.
Step 2
Remove existing front seat headrests from vehicle by disengaging the pole guide lock and lifting the headrest in upwards direction.
NOTE: Identify the type of seat back by inspecting the rear of the seat if it is plastic it is a hard back type, if it is a material type it is a soft back type.
(more…)

[Read more →]

This is how I installed my Eurojet Intercooler, hopefully its helpful to you.
Basic Steps
Removing the bumper fascia
Remove the bumper
Removing OEM intercooler and piping.
Install new intercooler, bumper and piping.
Trim and Re-install bumper fascia
(more…)

[Read more →]