Automotive Manual PDF

PROCEDURE:
1. Remove push type retainers from lower splash shield. Remove plastic splash shield to access to mounting location.
2. Locate and remove bolts that hold the frame brace and bumper brackets to vehicle.
3. Install frame bracket between lower radiator support and frame brace using (3) existing bolts. As shown.
4. Cut plastic splash shield to allow brackets to pass through. See Cutting Instruction sheet for guidelines on cutting. Reinstall plastic splash shield over brackets in this same order removed.
(more…)

[Read more →]

Modifying your vehicle ride height may result in the vehicle handling differently than a factory equipped vehicle. Extreme care must be used to prevent loss of control or vehicle rollover. Failure to drive your modified vehicle safely may result in serious injury or death. ReadyLift Suspension Inc. does not recommend the combined use of suspension lifts, body lifts, or other lifting devices. You should never operate your modified vehicle under the influence of alcohol or drugs. Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions. Always wear your seat belt.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
STEP 2. Read and understand instructions completely before beginning installation.
STEP 3. Determine passenger and driver mount brackets from figure above.
STEP 4. Remove the (16) push type retainers and (2) 6mm bolts from the lower splash shield. Remove plastic splash shield to gain access to mounting locations.
STEP 5. Locate the (4) 14mm holes in the lower radiator support. Attach the mount brackets using the (4) 1/2-13 x 1.00” hex head bolts, (4) 1/2” external-internal tooth lock washer, (4) 1/2” flat washer, (4) 1/2” lock washer, (4) 1/2-14 hex nuts, (2) 5/16-18 x 1.75” hex head bolts, (2) 5/16” lock washer, (2) 5/16” flat washers and (2) 5/16-18 flange lock nuts. Leave loose.
CAUTION: Wheels must be supported to support sub-frame to the unibody to avoid misalignment for re- attachment.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
STEP 2. Read and understand instructions completely before beginning installation.
STEP 3. Determine Driver and Passenger Uprights and Top and Bottom Tubes. (Uprights are positioned so raised side of bolt holes are facing each other and the Tube with the two pierced holes is the Bottom Tube).
(more…)

[Read more →]

STEP 1. Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning
STEP 2. Determine passenger and driver uprights and center section assembly and assemble as shown. Hand tighten all fasteners centered in slots or holes. Be sure dimple in ring mount plate is to the top.
STEP 3. For easier installation, it may be necessary to remove grille from vehicle but it’s not necessary on all models. Remove plastic shroud to gain access to grille by removing seven plastic pin retainers. Pull center pin up with a small flat tip screwdriver. Remove 6mm bolt from top of grille. Pull on outer edge of grille by applying firm pressure away from the fender, repeat on the opposite side and center section. Carefully remove grille from vehicle.
(more…)

[Read more →]

Zone Offroad Products recommends this system be installed by a professional technician. In addition to these instructions, profes-
sional knowledge of disassembly/ reassembly procedures and post installation checks must be known. Minimum tool requirements
include the following: Assorted metric and standard wrenches, hammer, hydraulic floor jack and a set of jack stands. See the “Special
Tools Required” section for additional tools needed to complete this installation properly and safely.
(more…)

[Read more →]

Modifying your vehicle ride height may result in the vehicle handling differently than a factory equipped vehicle. Extreme care must be used to prevent loss of control or vehicle rollover. Failure to drive your modified vehicle safely may result in serious injury or death. ReadyLift Suspension Inc. does not recommend the combined use of suspension lifts, body lifts, or other lifting devices. You should never operate your modified vehicle under the influence of alcohol or drugs. Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions. Always wear your seat belt.
(more…)

[Read more →]

For Chevrolet / GMC models 2500 & 3500, model years 2001-2008, with Duramax diesel engines: Extended Cab Short and Long Bed: also Crew Cab Short and Long Bed.
Note: Each tank has the above identification designation on its top. Please check to be sure the tank is properly identified as the one to fit your truck.
(more…)

[Read more →]

Certain Zone Suspension Products are intended to improve off-road performance. Modifying your vehicle for off-road use may result in the vehicle handling differently than a factory equipped vehicle. Extreme care must be used to prevent loss of control or vehicle rollover. Failure to drive your modified vehicle safely may result in serious injury or death. Zone Offroad Products does not recommend the combined use of suspension lifts, body lifts, or other lifting devices. You should never operate your modified vehicle under the influence of alcohol or drugs. Always drive your modified vehicle at reduced speeds to ensure your ability to control your vehicle under all driving conditions. Always wear your seat belt.
(more…)

[Read more →]

Pre-Installation Notes
1. Special literature required: OE Service Manual for model/year of vehicle. Refer to manual for proper disassembly/reassembly procedures of OE and related components.
2. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the OE manual.
3. Larger rim and tire combinations may increase leverage on suspension, steering, and related components. When selecting combinations larger than OE, consider the additional stress you could be inducing on the OE and related components.
4. Post suspension system vehicles may experience drive line vibrations. Angles may require tuning, slider on shaft may require replacement, shafts may need to be lengthened or trued, and U-joints may need to be replaced.
(more…)

[Read more →]