Automotive Manual PDF

1. Remove contents and check for damage. Verify all parts are present. Read instructions completely before installation.
2. Locate driver side mounting locations on vehicle (See Figure 1and 2). Repeat for passenger side.
3. Attach driver side front and rear mounting brackets to underside of rocker panel as shown using M8 hex bolts, 5/16” flat washer and 5/16” lock washer. Hand tighten only (See Figure 1 and 2). Repeat for passenger side.
(more…)

[Read more →]

Apply for below vehicle:
2000-2007 Chevy Silverado 1500 Crew Cab
2000-2007 GMC Sierra 1500 Crew Cab
2001-2007 Chevy Silverado HD Crew Cab
2001-2007 GMC Sierra HD Crew Cab

2006 and newer General Motors trucks have a larger cab mount bolt than in previous years. You will need to reuse your factory cab mount bolts when installing this kit on those trucks.
(more…)

[Read more →]

Installation Instruction:
1. Verify all the parts from the list above are present and accounted for. Please read instructions completely before starting.
2. Verify passenger and driver side bracket.
3. Locate the round holes on rocker panel for bracket installation. Insert M8 hex nut on the longer end of U-bolt. Insert U-bolt through the first hole and out through the second hole. Install M8 hex nut on shorter end of U-bolt after it comes through second (more…)

[Read more →]

Step Installation: Complete Part One, then find the section for specific instructions for your model vehicle.
Part One: Rear bracket attachment
Step 1) Attach the rear brackets to the step as shown in Figure 1, using a washer, E, and nut, I, on each stud. Tighten each nut.
Step 2) Place the cross member in position as shown in Figure 2, and secure using washers D and F, and one nut, H on each stud. Leave fasteners loose, as the bracket slots will be used to determine exact fit of rear upright bracket.
(more…)

[Read more →]

Installing the cab skirts: Remove any mud guards or stepping bars from the truck. Open the door on the truck and hold the cab side skirt in place. Secure the front part of the side skirt in the wheel well with the factory screw from the mud guard, then close the door and check to see that you have about a ¼” door gap between the bottom of the door and the side skirt. While holding the side skirt in place open the door and with a 1/8” drill bit, drill through the existing holes in the side skirt. Then secure the side skirt with the screws supplied in the hardware packet. While holding the rear portion of the cab side skirt in place drill a 1/8” hole through the side skirt and into the rocker panel and secure it with the screw supplied in the hardware packet as shown in fig.A. We have supplied you with two braces to secure the lower portion of the side skirt, install them evenly apart as shown in fig.B
(more…)

[Read more →]

Specially designed Chevrolet Corvette adapters (see Figure 1) can be used with the Universal Measuring System’s (UMS) pinchweld stands/adapter tubes or with Universal Anchoring System (UAS) bases. The adapters allow the positive anchoring of Chevrolet Corvettes (1997 - ).

The Corvette anchoring components allow attachment of hold down brackets to oval holes on underside of vehicles rocker panels. The hold down brackets then mount to either UMS basic stands/adapter tubes or to clamp bar tubes inserted in UAS bases.
(more…)

[Read more →]

BMW 3 Series (with side jack lifting holes) Clamping Setup
1. Remove conventional clamp jaws.
2. Attach BMW clamping adapter (518315), 1/4 inch spacer (532196) and outer pin support (518313) to pinchweld clamps as shown.
3, Remove plugs in bottom of rocker panels and jacking holes.
4. Lower vehicle onto supports while guiding outer support pins (618302) into jacking holes.
5. Tighten thumbscrew to hold pin in place.
NOTE: Use support bolt holes on clamping adapter
(more…)

[Read more →]