Automotive Manual PDF

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 1/2″, 9/16″, 12,14,15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

Step 1
Remove the driver’s side hood cover by prying upward with both hands.
Step 2
Remove the driver’s side windshield molding. Do not peel off the rubber seal or separate from roof molding.
Step 3
Remove 4 screws from driver’s side roof railing. Remove roof and windshield molding and set it down on the table.
Step 4
Measure 1” from the beginning of the roof railing and mark on the masking tape the spot to drill ―” hole for your harness.
(more…)

[Read more →]

These instructions explain the procedure required to mount either the Windjammer IV or Vindicator II fairing to your motorcycle. We urge you to follow the preparation and assembly sequence from start to finish. This will benefit you directly in several ways:
1) You will be assured the fairing is properly installed and is immediately ready for operation.
2) You will minimize unnecessary confusion, moaning and scraped knuckles.
3) You will protect your investment by doing it right, and
4) With the confidence that nothing has been overlooked, you won’t have to waste time backtracking to correct mistakes. That’s time you could spend riding.
(more…)

[Read more →]

Removing the stock air inlet system
a) Pry loose the retaining buttons on the lower splash shield.
b) Remove all retaining buttons on the fender liner around the fender well.
c) Carefully pull back the fender liner and splash shield to gain access to the fender well and stock resonator box.
d) Remove the battery from the engine bay.
e) Remove the plastic battery tray.
(more…)

[Read more →]

Congratulations on your purchase of the Honda 750 Ace & Spirit Thunder Air Filter Kit. We’re sure you’ll be pleased with the new level of performance you’ll experience. This kit should be installed on bikes with After Market Exhaust Pipes only and jetted, (jet kit not included). We recommend that an experienced mechanic perform this conversion. Use the appropriate Honda service manual for reference to complete jetting of carbs. Remember, gasoline is extremely flammable and can be explosive under certain conditions. Work in a well-ventilated area and clean up any spills immediately. Check for leaks before riding.
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

These instructions will take you through the installation of your new air intake system for your vehicle. We always recommend that you keep your stock air intake system in storage in case you might need it later.
Kit includes: air filter, air intake tube, bracket, (2) 3” hose clamps, red connecting hose and rubber grommet.
Tools required: Phillips head screwdriver and 5/16” nut driver.
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.

SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.

SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, and jack stands
(more…)

[Read more →]