Automotive Manual PDF

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 1/2″, 9/16″, 12,14,15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

Installation Instructions. Read Me!
I) DISCONNECT NEGATIVE (-) BATTERY CABLE.
II) Remove the Factory Air Box
a) Loosen Mass Air Meter hose clamps and set meter aside.
b) Unbolt the three air box hold down fasteners and save the bolts. See Fig#1
c) Lift out & remove the factory air box assembly from vehicle.
d) Remove and save the three rubber grommets, inserts and bolts. See Fig#2
(more…)

[Read more →]

These instructions explain the procedure required to mount either the Windjammer IV or Vindicator II fairing to your motorcycle. We urge you to follow the preparation and assembly sequence from start to finish. This will benefit you directly in several ways:
1) You will be assured the fairing is properly installed and is immediately ready for operation.
2) You will minimize unnecessary confusion, moaning and scraped knuckles.
3) You will protect your investment by doing it right, and
4) With the confidence that nothing has been overlooked, you won’t have to waste time backtracking to correct mistakes. That’s time you could spend riding.
(more…)

[Read more →]

Getting started
a) Make sure vehicle is parked on a level surface, and set parking brake.
b) Disconnect negative battery terminal.
c) If engine has run within the past two hours let it cool down.

Removing the stock air inlet system
a) Remove the stock air box assembly and attaching hardware from inside the fender well.
b) Disconnect breather hose from the air inlet tube.
c) Disconnect air temperature sensor harness from the air inlet tube.
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.
SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.

SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, jack stands
(more…)

[Read more →]

When installing this exhaust system make sure to use proper safety precautions. Use jack stands when working under the vehicle, set parking brake, block tires and use safety glasses and gloves. Allow exhaust to cool before attempting installation. Severe injury or burns could occur if safety measures are not taken.

SUGGESTED TOOLS: 1/2″, 9/16″, 15mm wrenches & sockets, WD-40, hacksaw, and jack stands
(more…)

[Read more →]

Lay out the exhaust on the floor so it looks like the drawing and compare parts with manual. To remove the stock exhaust, un-clamp it just in front of the muffler. You may need to heat it up for easier removal. Leave all rubber grommets in place. Use WD-40 to aid in removal of exhaust and the hangers. Now cut off your stock tailpipe just behind the muffler
(more…)

[Read more →]

1. Disconnect both negative battery cables. Unlatch all four factory clips on the factory airbox.
2. Remove factory air filter by separating the inlet and outlet sections of the assembly.
3. The filter is held in place by two rubber grommets on the bottom.(Note: make sure factory grommets remain in lower air box support.)
(more…)

[Read more →]