Automotive Manual PDF

RSS Feed

The Resources for Automotive

Fixed a sideview mirror on a Mercedes?

January 3rd, 2011 · No Comments

I hit a pole backing up in my tight apartment garage and while the outside of my mirror broke my actual mirror just popped out. I can pop it back in with trial and error but if i shut my door too hard it pops out again. It’s still connected to string. Please tell me I don’t have to go to the dealer!
(more…)

[Read more →]

1998-2007 Toyota Land Cruiser Signal Mirror Installation Instructions

July 23rd, 2010 · No Comments

1. Start with the driver’s side door and lower the window. (A) 2. Use a small slotted screwdriver to remove the plastic screw cover located on the inside section of the door. (B) 3. Remove the screw behind the screw cover and the screw located directly below the corner speaker. (C) 4. Starting at the top edge, use a small pry bar to lift the window control panel out of the door panel. (A) 5. Disconnect both sets of wires from the window control panel. (B) 6. Remove the screw in the opening from where the window control panel was removed. (C) 7. Starting from the left side, use a small slotted screwdriver to pry open the cover above the door handle. Remove the screw behind the cover. (A) 8. (more…)

[Read more →]

GB Fitting Instructions for Basic Carrier

March 28th, 2010 · No Comments

First Time Installation
Remove parts from packaging and check contents. Contact your Prorack dealer if parts are missing or damaged.
This kit fits type A, B and C.
These instructions show type A crossbar fitted. They also apply to type B and C.
NOTE: Clamp images in these instructions may not be representative of the clamps in this kit
Use keys to remove covers.
Use hex screwdriver to reverse adjusting screw 10 turns.
Press adjusting screw and pull crossbar legs out. Refer to the crossbar instructions for crossbar adjustment. Ensure each end of the crossbar is adjusted equally ‘X’.
(more…)

[Read more →]

H2 Hummer Low Profile Light Bar Instructions

January 27th, 2010 · No Comments

INSTALLATION:
1. Disconnect negative battery terminal. Remove phillips head screw from driver side marker light lens and remove lens assembly. Pull up the wire boot.
2. Remove driver side assist handle by pulling out locking tabs with a small flat blade screwdriver until they “click”. Next, remove the A-Pillar trim and place on dash.
3. Remove the fuse cover panel on the left side of dash. There are two clips at the top and one at the bottom.
4. Using a 13mm socket, remove 4 bolts, one plastic stud, and remove the driver’s side hood stop bracket for access to the main wire harness boot.
(more…)

[Read more →]

1994-97 Chevrolet/GMC S-10/Sonoma I4 – 2.2L Installation Instructions

September 1st, 2009 · No Comments

NOTE: This kit was not designed to fit vehicles with a body lift.
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the vehicle’s air temperature sensor.
3. Loosen the hose clamp at the air intake plenum.
4. Remove the air box from the vehicle by sliding upwards.
5. Remove the air temperature sensor from the stock air intake tube.
(more…)

[Read more →]

Ford Zetec E Engine Supplement

April 30th, 2009 · No Comments

The most common engine fitment is the Ford Zetec E, however, Ford Duratec, Ford Pinto and Ford Cosworth engine fitments are also available from GKD. Customers have also previously made their own engine and gearbox mounts for the Ford V4 and V6 as well as the Mazda and Rover V8 engines. Please consult GKD for advice on suitability. GKD are always ready to advise on engine builds and ancillary equipment.
(more…)

[Read more →]

Ford Focus PRO-FIT Linear Fuel Doors – Installation Instructions

March 20th, 2009 · No Comments

Do not perform this install near a flame source due to the risk of fire or explosion from gas fumes. Use a jack to lift rear of vehicle. Remove the passenger side rear tire. Remove the wheel well cover to expose the fuel filler neck behind the quarterpanel.
Note: For manual locking or manual non-locking fuel doors, do steps 1-4 only. For electric locking fuel doors, do all steps.
(more…)

[Read more →]

Nemesis Engine Control for Ducati

February 5th, 2009 · No Comments

The Nemesis uses both of the original multi-pin connectors to link with your bike wiring loom, no changes are necessary, but remember it is VITALLY important to re-connect the 6mm ground connector. Nemesis also re-uses the cast aluminium ‘heat sink’ from the IAW 5.9 ECU, this can be removed and re-fitted to Nemesis using a TORX T20 screwdriver without any damage to the original ECU.
(more…)

[Read more →]

Ducati Electronic Jet Kit Instructions

January 27th, 2009 · No Comments

Thank you for choosing the Techlusion Electronic Jet Kit, the TFI. The TFI is usable for fuel injected Ducati’s ** . This product is a perfect fit for stock bikes with exhaust and intake mods. It is also capable of handling the fuel needs of cubic inch kits, light cams, and a variety of head porting. This is an Electronic Jet Kit. Like jet kits in the past, the more you modify, the more responsibility you take in getting your fuel curve right. Going to www.dobeckperformance.com will help you obtain better high horsepower tuning.
(more…)

[Read more →]

Chevrolet C5 Corvette Figure Grille Set Installation Manual

November 5th, 2008 · No Comments

Thank you for purchasing Figure’s 1997-2004 Chevrolet C5 Corvette Custom Grille set. These grilles have been engineered to enhance the look of your vehicle for the duration of its life. Proper installation is essential to your overall satisfaction, so please read these instructions before attempting to install the grilles. Exercise patience; these instructions are intended to assist even the most mechanically challenged.
(more…)

[Read more →]