Automotive Manual PDF

Be sure to test the heaters to make sure they work properly before going to the trouble of installing them. I just connected them to my battery terminals to do a quick test. This should only take a couple minutes and is a worthwhile precaution. Additionally, I would recommend getting some upholstery hog rings and hog pliers. These can be purchased as a package from JCWhitney for about $4-5.
(more…)

[Read more →]

1. Pull down chrome collar and carefully unscrew and remove the stock shift knob.
2. Remove the front console cover. Pull up from the front to unclip the clips and remove from the vehicle.
3. Remove the 2 screws securing the front part of the console. Remove any additional screws that may be holding the center part of the console in place, this may vary by year and model. Lift the 2 tabs shown to the right over the center section of the console so that they rest on the outside of the console assembly.
(more…)

[Read more →]

1. Unscrew the stock shift knob by rotating it counter clockwise.
2. Remove all screws securing center console and remove console.
3. Remove the rubber dust boot surrounding the shifter, use caution not to damage it. Put it in a safe place for re-installation later.
4. Place the car up on a lift, or use a jack and jack stands to raise it off the ground. Loosen the nut on the base of the shifter using a 12mm socket and ratchet. You may need to hold the head of the bolt on the opposite side of the shift rod with a wrench to loosen the nut.
(more…)

[Read more →]

Please read this Owner’s Manual carefully before using the rear camera, and keep this manual in the glove box for future reference. This product is designed to be used exclusively on an Acura RL. Acura is not responsible if the unit is used for any other intended purpose.
(more…)

[Read more →]

This chapter provides information required for the installation of the Neo Changer, it must be read by all users. Thank you for purchasing the Neo Changer. Since the Neo Changer will works in many different vehicles the following steps must be taken to ensure the changer is set up correctly for the vehicle it is being installed in.
(more…)

[Read more →]

1. Before working, please make sure the vehicle power is off (please keep in mind when pulling out the key, only monitor supply would be off but whole vehicle power supply would be off 5 minutes later)
2. Starting with separating of the monitor and the connecter removed in working may causes a error code. Do not start until the work is done.
(more…)

[Read more →]

A) To remove left handlebar:
1. Remove bar end weights.
2. Cut two small cable ties holding wire loom from left control housing (PHOTO 1)­ one under the handlebar anti­ rotation bracket and the other attaching the wire loom to the underside of the top triple clamp. Do the same on the right side.
3. Remove the clutch master cylinder from the left bar.
4. Remove the forward plastic control housing cover (2 screws) Loosen the two screws that sandwich the bar between the forward plate and the rear half of the left control housing(PHOTO 2).
5. Remove the two screws attaching the left handgrip sleeve to the left bar tube­1 on top and 1 on the bottom (PHOTO 3).
6. Remove the anti rotation bracket holding screw located under the top triple clamp (PHOTO 4).
7. Loosen the two screws clamping the left bar to the triple clamp. Only the inner most crew needs to be removed to withdraw the stock bar.
(more…)

[Read more →]

The SA314 speaker bracket mounts on the left side crash bar of your motorcycle. If you have a light mounted here, the bracket mounting screws may share some or all of the mounting holes.
1. Secure the mounting brackets to the SA314 speaker using the provided hardware. Make sure that the brackets are properly oriented before proceeding.
2. Now secure the bracket onto the motorcycle using the supplied mounting hardware as shown below.
3. Connect the speaker to your siren as outlined in your siren installation manual.
(more…)

[Read more →]

Heli Bars are designed to safely increase your riding comfort, however it is imperative that these instructions be followed to ensure correct installation. Failure to follow these instructions could result in improper installation and create a dangerous control situation.
(more…)

[Read more →]

Refer to your Owner’s Manual for instructions on lowering and removing the canvas top. ALL hardware for your soft top should be removed. This includes the trim around the body. Some of the screws from the Canvas Top Hardware will be used in the Hardtop installation, so keep them available.
(more…)

[Read more →]