Automotive Manual PDF

This chapter provides information required for the installation of the Neo Changer, it must be read by all users. Thank you for purchasing the Neo Changer. Since the Neo Changer will works in many different vehicles the following steps must be taken to ensure the changer is set up correctly for the vehicle it is being installed in.
(more…)

[Read more →]

1. Before working, please make sure the vehicle power is off (please keep in mind when pulling out the key, only monitor supply would be off but whole vehicle power supply would be off 5 minutes later)
2. Starting with separating of the monitor and the connecter removed in working may causes a error code. Do not start until the work is done.
(more…)

[Read more →]

A) To remove left handlebar:
1. Remove bar end weights.
2. Cut two small cable ties holding wire loom from left control housing (PHOTO 1)­ one under the handlebar anti­ rotation bracket and the other attaching the wire loom to the underside of the top triple clamp. Do the same on the right side.
3. Remove the clutch master cylinder from the left bar.
4. Remove the forward plastic control housing cover (2 screws) Loosen the two screws that sandwich the bar between the forward plate and the rear half of the left control housing(PHOTO 2).
5. Remove the two screws attaching the left handgrip sleeve to the left bar tube­1 on top and 1 on the bottom (PHOTO 3).
6. Remove the anti rotation bracket holding screw located under the top triple clamp (PHOTO 4).
7. Loosen the two screws clamping the left bar to the triple clamp. Only the inner most crew needs to be removed to withdraw the stock bar.
(more…)

[Read more →]

The SA314 speaker bracket mounts on the left side crash bar of your motorcycle. If you have a light mounted here, the bracket mounting screws may share some or all of the mounting holes.
1. Secure the mounting brackets to the SA314 speaker using the provided hardware. Make sure that the brackets are properly oriented before proceeding.
2. Now secure the bracket onto the motorcycle using the supplied mounting hardware as shown below.
3. Connect the speaker to your siren as outlined in your siren installation manual.
(more…)

[Read more →]

Heli Bars are designed to safely increase your riding comfort, however it is imperative that these instructions be followed to ensure correct installation. Failure to follow these instructions could result in improper installation and create a dangerous control situation.
(more…)

[Read more →]

Refer to your Owner’s Manual for instructions on lowering and removing the canvas top. ALL hardware for your soft top should be removed. This includes the trim around the body. Some of the screws from the Canvas Top Hardware will be used in the Hardtop installation, so keep them available.
(more…)

[Read more →]

The gear indicator comes configured for use with the OEM Suzuki gear position sensor, and is fitted with standard connectors to plug directly into the Suzuki wiring harness. The unit also features the so-called ‘TRE’ modification, which is designed to defeat the gear dependent mapping strategy of the Suzuki ECU. Please refer to the bottom of this document for a description of the TRE function.
(more…)

[Read more →]

The gear indicator comes configured for use with the OEM Suzuki gear position sensor, and is fitted with standard connectors to plug directly into the Suzuki wiring harness. The unit also features the so-called ‘TRE’ modification, which is designed to defeat the gear dependent mapping strategy of the Suzuki ECU. Please refer to the bottom of this document for a description of the TRE function.
(more…)

[Read more →]

The following steps need to be performed from underneath the vehicle:
• Remove the three 7 mm screws holding the front fascia inside the radiator opening.
• Next, remove the 7 mm screws on either side (one on each side). These are the screws holding the bottom of the bumper cover - see picture.
(more…)

[Read more →]

Disconnect electrical connector for under hood light & unclip electrical connector for under hood light from the radiator shroud. Disconnect the electrical connector from outside air temp sensor located low on the right side of the shroud. Remove the 2 “christmas tree” push fasteners holding the radiator shroud to the condenser. They are located approximately midway up along each side. Raise front of vehicle, follow manufacturer instructions. Use jack stands to support vehicle.
(more…)

[Read more →]