Automotive Manual PDF

1. Attach the left strake to the side under spoiler using the three self-tapping screws.
2. Remove the three self-tapping screws that fasten the front inner fender to the fenderwell.
3. Remove the four clips that fasten the existing side under spoiler to the side sill, then remove the spoiler by sliding it toward the front.
4. Remove the spring nut from the end of the side under spoiler you just removed.
5. Remove the eight clips from the side sill by turning them 45 degrees.
(more…)

[Read more →]

Adjusting the Control Unit
• Use a small flat-tip screwdriver to change the mode switch and the horn/siren switch and to adjust sensitivity
Mode Switch:
• Set the mode switch according to the customer’s choice.
• Refer to the Owner’s Manual for the explanation of each mode.
Horn/Siren Switch:
• Set the switch to “HORN” in normal use. If an optional siren is installed, set the switch to “SIREN.”
(more…)

[Read more →]

1. If equipped, make sure that you have the anti-theft code for the radio, then write down the frequencies for the preset buttons on the radio.
2. Slide the driver’s seat completely to the rear.
3. Disconnect the negative cable from the battery.
4. Open the glove box. Squeeze the retaining tabs, and remove the stop. Pull the glove box down.
5. Remove the driver’s dashboard lower cover (two self-tapping screws, four retaining clips and one connector).
6. Remove the lower console cover.
(more…)

[Read more →]

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE:
• Be extremely careful not to damage the body.
• To prevent damage, rest the front bumper on a blanket or cardboard during the installation.
• Before removing parts, note their locations so that they can be reinstalled in their original locations properly.
(more…)

[Read more →]

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE: These installation instruction show the left fog light begin installed. The same procedure applies to installing the right fog light.
(more…)

[Read more →]

INSTALLATION
1. Make sure you have the anti-theft code for the audio system and the navigation system (if equipped).
2. Disconnect the negative cable from the battery.
Removing the vehicle parts
3. Shift the select knob to “D” position by pressing down on the shift lock stopper with the ignition key. Remove the left side center panel (eight clips and unplug the vehicle connectors).
4. Remove the right side center panel (ten clips and unplug the vehicle connector).
(more…)

[Read more →]

GUARDIAN MODULE - Remove the lower dash panel below the steering column. The Guardian Module should be positioned in a secure area below the steering column. It can be secured using self tapping screws, adhesive foam tape, or wire ties. Do not secure the module until all harnesses are installed and proper lift operation has been verified.
(more…)

[Read more →]

Application Chevy/GMC Full Size Van (GMT 610) 2008 - All Engines 2009 - All Engines except 6.6L
GUARDIAN MODULE - Remove the lower dash panel below the steering column. The Guardian Module should be positioned in a secure area below the steering column. It can be secured using self tapping screws, adhesive foam tape, or wire ties. Do not secure the module until all harnesses are installed and proper lift operation has been verified.
(more…)

[Read more →]

The most common engine fitment is the Ford Zetec E, however, Ford Duratec, Ford Pinto and Ford Cosworth engine fitments are also available from GKD. Customers have also previously made their own engine and gearbox mounts for the Ford V4 and V6 as well as the Mazda and Rover V8 engines. Please consult GKD for advice on suitability. GKD are always ready to advise on engine builds and ancillary equipment.
(more…)

[Read more →]

The siren speaker wires must exit through the bottom of the siren. The siren wire hole is also the drainage hole. Improper mounting will damage the driver and void the warranty. Sirens produces extremely loud emergency warning tones! Exposure to these tones without proper and adequate hearing protection, could cause ear damage and/or hearing loss!
(more…)

[Read more →]