Automotive Manual PDF

Step One: Locate Hardware kit. Check contents with hardware.
Step Two: Remove the front body mount plastic covers.
Step Three: Place the front bolt B plate through the body as shown in pic 2. Attach front support bracket.
Step Four: Place the rear bolt plate through the body as shown in pic 3. Attach rear support bracket.
(more…)

[Read more →]

1. Remove contents and check for damage. Verify all parts are present. Read instructions completely before installation.
2. Locate driver side mounting locations on vehicle (See Figure 1and 2). Repeat for passenger side.
3. Attach driver side front and rear mounting brackets to underside of rocker panel as shown using M8 hex bolts, 5/16” flat washer and 5/16” lock washer. Hand tighten only (See Figure 1 and 2). Repeat for passenger side.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
STEP 2. Read and understand instructions completely before beginning installation.
STEP 3. Determine passenger and driver mount brackets from figure above.
STEP 4. Remove the (16) push type retainers and (2) 6mm bolts from the lower splash shield. Remove plastic splash shield to gain access to mounting locations.
STEP 5. Locate the (4) 14mm holes in the lower radiator support. Attach the mount brackets using the (4) 1/2-13 x 1.00” hex head bolts, (4) 1/2” external-internal tooth lock washer, (4) 1/2” flat washer, (4) 1/2” lock washer, (4) 1/2-14 hex nuts, (2) 5/16-18 x 1.75” hex head bolts, (2) 5/16” lock washer, (2) 5/16” flat washers and (2) 5/16-18 flange lock nuts. Leave loose.
CAUTION: Wheels must be supported to support sub-frame to the unibody to avoid misalignment for re- attachment.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list. Read and understand instructions completely before beginning installation.
STEP 2. Measure, and mark clearly, from the front of pinch weld towards the rear of vehicle for bracket positions. Suggested locations at 14 1/2”,33 1/4”, 49 1/2” and 61 1/2”.
STEP 3. Drill 5/16” holes as marked on pinch weld. Drill each hole in pinch weld so they are centered vertically.
STEP 4. Under the vehicle near the first 2 hole locations you will see 2 black body plugs, remove these
(more…)

[Read more →]

REAR SETUP (45” hose)
STEP 1: Lift the vehicle off the ground with a jack or on a stand. Remove the stock shock absorber from the vehicle. Install the Elka shock absorbers on the vehicle. The banjo bolt must face towards the front of the vehicle with the hose coming out on the left side. The rebound adjuster located at the bottom of the shock should face the rear of the quad for convenient access. The bottom fork of the shock can be turned 180° clockwise if needed.
(more…)

[Read more →]

Apply for below vehicle:
2000-2007 Chevy Silverado 1500 Crew Cab
2000-2007 GMC Sierra 1500 Crew Cab
2001-2007 Chevy Silverado HD Crew Cab
2001-2007 GMC Sierra HD Crew Cab

2006 and newer General Motors trucks have a larger cab mount bolt than in previous years. You will need to reuse your factory cab mount bolts when installing this kit on those trucks.
(more…)

[Read more →]

BRACKET MOUNTING INSTRUCTIONS
Step 1. Remove contents from box and check for damage. Verify all parts against parts list. Read and understand instructions completely before installation.
Step 2. Position and hold template on passenger side for quick latch bracket as shown (See Figure 1). (FOR TOYOTA, NISSAN, CHEVY S-10, GMC up to 94, and MAZDA up to 94 a separate bracket kit must be ordered). Using a center punch, punch each hole. NOTE: If the truck has a bed liner, center punch the bed liner. DO NOT CUT THE BED LINER! Repeat for driver side.
(more…)

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list. Read and understand instructions completely before beginning installation.
STEP 2. Position and hold template on passenger side for square bracket as shown (See Figure 1). (FOR TOYOTA, NISSAN, CHEVY S-10, GMC up to ‘94, and MAZDA up to ‘94 Use template for “L” bracket as shown in Figure 4). Using a center punch, punch each hole. NOTE: If the truck has a bed liner, center punch the bed liner. DO NOT CUT THE BED LINER! Repeat for driver side.
STEP 3. Verify hole locations before drilling (See Figure 2). Drill mounting holes for square brackets using 9/64” drill bit (See Figure 2). For “L” bracket mounting, drill mounting holes using 7/32” drill bit (See Figure 4). Repeat for driver side.
(more…)

[Read more →]

F-150 QUICK LATCH MOUNTING BRACKET INSTRUCTIONS
Step 1. Remove contents from box and check for damage. Verify all parts against parts list. Read and understand instructions completely before installation.
Step 2. Assemble brackets as shown in Figure 1.
Step 3. With lever towards the tailgate side insert lower hold-down bracket through lower hole on d-pillar.
Step 4. Insert upper hold-down bracket in upper hole of d-pillar.
(more…)

[Read more →]

Prefit Before Painting. Install new, unpainted parts according to these instructions.Then remove parts, paint them and re-install.
Painted or Altered Parts are Non-Refundable
Remove the factory step cover. In the center of the lower – front hole drill a 1/8” hole through the center of the second panel as shown in fig.A, this hole will give you access to attach the step cover with the longer screw supplied in the hardware packet. The remaining 3 screws must be used with a washer as shown in fig.B.
(more…)

[Read more →]