Automotive Manual PDF

RSS Feed

The Resources for Automotive

Why does my brake light stay on in my 2001 Nissan Maxima?

December 17th, 2010 · No Comments

I just changed the rear brakes on my 2001 Nissan Maxima by procedure and the Parking/ Emergency brake light continues to stay on even though the handle is in the down position. The light was not on before the repair.
(more…)

[Read more →]

Honda/Kawasaki/Suzuki/Yamaha Electronic Jet Kit Instructions

November 13th, 2009 · No Comments

INSTALLATION
1. Before installing the TFI you must first disconnect the negative lead from the battery.
2. Determine a location for the TFI unit. Suggested locations are as follows: Under the seat, behind a side cover or tail section.
3. The TFI comes with a harness with injector connectors that match the factory injector connectors.
4. Locate the factory fuel injectors (see owners manual if you are not sure)*.
(more…)

[Read more →]

Honda/Suzuki Electronic Jet Kit Instructions

November 9th, 2009 · No Comments

This product is a great fit for stock bikes with exhaust and intake mods. It is also capable of handling the fuel needs of big bore kits, light cams, and a variety of head porting. This is an Electronic Jet Kit. Like jet kits in the past, the more you modify, the more responsibility you take in getting your fuel curve right. Going to www.dobeckperformance.com will help you obtain better high horsepower tuning.
(more…)

[Read more →]

2005-2009 Ford F-250 Super Duty 4WD w/Camper Package ReadyLiftо Installation

August 13th, 2009 · No Comments

Pre-Installation Notes
1. Special literature required: OE Service Manual for model/year of vehicle. Refer to manual for proper disassembly/reassembly procedures of OE and related components.
2. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the OE manual.
3. Larger rim and tire combinations may increase leverage on suspension, steering, and related components. When selecting combinations larger than OE, consider the additional stress you could be inducing on the OE and related components.
4. Post suspension system vehicles may experience drive line vibrations. Angles may require tuning, slider on shaft may require replacement, shafts may need to be lengthened or trued, and U-joints may need to be replaced.
(more…)

[Read more →]

97-98 Ford Air Dam 4×2 and 4×4 Installation Instructions

June 26th, 2009 · No Comments

Tools needed: 8mm open end wrench or socket 7/16 socket or open end wrench 1/4×1 bolts, 5/16 flat washers and nuts
1. Using the 8mm wrench, remove the factory Air Dam.
2. Position Air Dam aligning the center hole of Air Dam with the center hole of bumper.
3. Using a bolt with flat washer on the bolt, push bolt up through Air dam into bumper.
4. Install a flat washer, and a locking nut from above. DO NOT tighten at this time.
5. Install the balance of the bolts making sure that a flat washer is against the Air Dam.
6. Once all bolts are installed, tighten starting from the center of the Air Dam working right and then center of the Air Dam working left.
(more…)

[Read more →]

Ducati Electronic Jet Kit Instructions

January 27th, 2009 · No Comments

Thank you for choosing the Techlusion Electronic Jet Kit, the TFI. The TFI is usable for fuel injected Ducati’s ** . This product is a perfect fit for stock bikes with exhaust and intake mods. It is also capable of handling the fuel needs of cubic inch kits, light cams, and a variety of head porting. This is an Electronic Jet Kit. Like jet kits in the past, the more you modify, the more responsibility you take in getting your fuel curve right. Going to www.dobeckperformance.com will help you obtain better high horsepower tuning.
(more…)

[Read more →]

Volvo short shifter kit installation instructions

December 9th, 2008 · No Comments

Tools required:
1. Flathead screwdriver.
2. Electrical crimper/cutter.
3. Fine needlenose pliers or c-clip remover (or even something with a pointy tip)
4. 4mm or 5/32” hex key, ideally a 3/8” driver style. A similar size of torx will do in a pinch. Driver extensions are very handy.
5. 8mm and 10mm socket driver.
6. Work light!
(more…)

[Read more →]

M-Force E36 Camber Plate Installation

October 28th, 2008 · No Comments

Thank you for purchasing the Adjustable Camber Plate kit from Vorshlag Motorsports. In order to ensure proper installation and longevity of your kit, Vorshlag Motorsports recommends that you have your plates professionally installed by a reputable shop. These instructions are basic guidelines for cars that do not have camber plates currently. Instructions for your car could be slightly different as well as starting points for installation. Socket sizes may vary. Please see the last page for help.
(more…)

[Read more →]

Ford F-250 / F-350 / F-450 Regular Cab (48”) Installation Guide

September 5th, 2008 · No Comments

To ensure our customers receive all components with full integrity, we pack the motors separate from their linkage assemblies. This requires that the installer position and fasten the motor before continuing with the install. Please follow the instructions below and handle the assembly carefully.
(more…)

[Read more →]

1999-2000 Chevrolet/GMC Silverado/Sierra 3/4 Ton 3″ Body Lift Kit

July 16th, 2008 · No Comments

1. Remove negative battery cable, then positive battery cable from the battery. If equipped, the Supplemental Restraint System will be deactivated when the battery is disconnected.
SteeRIng extenSIon
2. Remove the nut and bolt holding the steering column to the steering shaft located in the engine compartment about 8 inches down from the firewall. Mark the two shafts for realignment.
(more…)

[Read more →]