Automotive Manual PDF

RSS Feed

The Resources for Automotive

How do I setup bluetooth for my phone in my 2006 BMW x3?

December 19th, 2010 · No Comments

I have a 2006 BMW x3 and I would like to setup my phone to the cars bluetooth. However, I do not know how to do this. I referred to the manual, but it doesnt have clear instructions so I couldnt get it to work. A step by step list of instructions would be nice.
(more…)

[Read more →]

90-97 Mazda Miata NA Flush Mount Headlight Kit Installation Guide

August 17th, 2010 · No Comments

Each factory headlight is bolted to the car by only (3) nuts. Once the (3) nuts are unscrewed the headlight will be able to be removed from where it is bolted. In order to completely remove the headlight from the car you will have to unplug the factory wiring harness from the back of the headlight. To accomplish this remove the 4 screws holding the black plastic surround while the headlight is up. Loosen the four bolts holding the headlight lid on the assembly. Once removed, you will be able to gain access to the headlight to unplug the socket and associated clips. Now you can remove the headlight from the car. Below I will walk you through this entire process.
(more…)

[Read more →]

Hummer H3 Delta 6X Light Bar Installation Instructions

January 9th, 2010 · No Comments

Step 1
Remove the driver’s side hood cover by prying upward with both hands.
Step 2
Remove the driver’s side windshield molding. Do not peel off the rubber seal or separate from roof molding.
Step 3
Remove 4 screws from driver’s side roof railing. Remove roof and windshield molding and set it down on the table.
Step 4
Measure 1” from the beginning of the roof railing and mark on the masking tape the spot to drill ―” hole for your harness.
(more…)

[Read more →]

2006-2009 Hummer H3 & 2005-2009 Colorado/Canyon 4WD Torsion Key Kit Installation Instructions

January 6th, 2010 · No Comments

Step 1: Applies to H3 ONLY, for Colorado/Canyon please skip to step 2.
Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground using a floor jack and jack stands or a (2) two post lift if available.
First, remove driver’s side front wheel, then unbolt upper shock mounting nut. (A)
Next remove lower shock mounting nut and bolt. (B)
Remove shock. Install shock stem spacer provided and reinstall bushings and shock.
Verify that all fasteners have been tightened to the proper torque specs and re-install wheel.
*Be sure to torque the lug nuts to the proper OEM settings.
(more…)

[Read more →]

1986-93 Suzuki RM125 ESL450 Ignition/Lighting StatorFitting Instructions

December 24th, 2009 · No Comments

Read these instructions completely
Step 1:Take the ignition cover off. Are The Replacement Parts Similar? Compare the replacement part to the original. The replacement part should match, including the mounting hole locations. If not: Double check the application listing with your bike.
Step 2: Remove the flywheel using a proper puller. Remove the baseplate with the original stator. Disconnect the wires from the wiring loom.
Step 3: Remove existing stator coil off the baseplate and cut the wires close to the coil. Replace it with the new unit and feed the new leads though the holes in the baseplate.
(more…)

[Read more →]

HONDA CRF450X Flywheels Installation Instructions

December 19th, 2009 · No Comments

STEP 1: BEFORE YOU BEGIN
WARNING: ALL TRAILTECH FLYWHEELS WILL CHANGE THE PERFORMANCE OF YOUR VEHICLE. It is highly recommended that you spend the time necessary to familiarize yourself with the performance changes, and become comfortable with the way the bike produces power with the new part.
(more…)

[Read more →]

94-97 Honda Accord Sniper Hood

December 8th, 2009 · No Comments

STEP 1: Adjust hood until proper alignment with matching panels is achieved.
STEP 2: Adjust primary latch until it fits into the bar on the hood. Make sure when the hood is closed you can hear the latch “click” onto the hood.
STEP 3: After you here it click, test it to be sure it’s working properly by grabbing the front edge of the hood and slowly pulling upward with a steady even pressure. If the hood opens it’s not adjusted properly; repeat STEP 2 until hood cannot be pulled open after it’s closed.
(more…)

[Read more →]

Bulk Instructions Simple

December 5th, 2009 · No Comments

To get the most life and performance from RaceTEX bulk muffler packing, a mu ffler should be repacked with the core in it. Ideally, you would like to fill the front of the muffler first (the end closest to the engine) and work towards the exit. This isn’t always possible as with mufflers that have cores welded to the rear end-cap (Honda CRF150R, White Brothers E-Series for example).
(more…)

[Read more →]

2002-Up ACURA RSX including 6-spd Type-S Precision Sport Shifter Installation

November 16th, 2009 · No Comments

This B&M Precision Sport Shifter has been designed to work on most 2002+ Acura RSX/Honda Integra (including 6- spd Type-S) and 2001+ Honda Civic models equipped with a manual transmission. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Precision Sport Shifter. Installation of the B&M Precision Sport Shifter can be accomplished by anyone with minimal mechanical experience.
(more…)

[Read more →]

JackRabbit Honda Ridgeline Instructions

November 8th, 2009 · No Comments

STEP 1: REMOVE PLYWOOD & INVENTORY CONTENTS
Remove the top cover from the canister box and set it aside for later installation.
Remove the canister from the box. Using the 3/8” wrench or socket remove the 2 bolts holding the plywood on the ends of the canister. Use Side Cut Pliers to cut handle retaining straps. DISCARD PLYWOOD PACKAGING AND BOLTS!
Perform a quick inventory to insure all parts are there. Be sure to check inside the small cardboard box for parts.
(more…)

[Read more →]