Automotive Manual PDF

RSS Feed

The Resources for Automotive

Jeep Remote Keyless Entry (RKE) Programming Procedures

July 20th, 2010 · No Comments

A Remote Keyless Entry (RKE) Programming Procedures Card (Publication No. 81-170-00011) is being provided with this Technical Service Bulletin to simplify RKE transmitter programming on 1999 – 2002 North American vehicles. Additional copies of the RKE publication, 81–170–00011 (Fig. 1), can be ordered from DDS Distribution Services, LTD. Their number is 1-800-890-4038.
NOTE: THE RECENTLY RELEASED MILLER SPECIAL TOOL, “RF DETECTOR NO. 9001″, SHOULD BE USED TO DETERMINE IF THE TRANSMITTER IS WORKING BEFORE BEGINNING PROGRAMMING PROCEDURES. THE RF DETECTOR INDICATES IF THE TRANSMITTER IS WORKING, NOT IF IT IS PROGRAMMED TO A VEHICLE.
(more…)

[Read more →]

Hummer H3 Delta 6X Light Bar Installation Instructions

January 9th, 2010 · No Comments

Step 1
Remove the driver’s side hood cover by prying upward with both hands.
Step 2
Remove the driver’s side windshield molding. Do not peel off the rubber seal or separate from roof molding.
Step 3
Remove 4 screws from driver’s side roof railing. Remove roof and windshield molding and set it down on the table.
Step 4
Measure 1” from the beginning of the roof railing and mark on the masking tape the spot to drill ―” hole for your harness.
(more…)

[Read more →]

1986-93 Suzuki RM125 ESL450 Ignition/Lighting StatorFitting Instructions

December 24th, 2009 · No Comments

Read these instructions completely
Step 1:Take the ignition cover off. Are The Replacement Parts Similar? Compare the replacement part to the original. The replacement part should match, including the mounting hole locations. If not: Double check the application listing with your bike.
Step 2: Remove the flywheel using a proper puller. Remove the baseplate with the original stator. Disconnect the wires from the wiring loom.
Step 3: Remove existing stator coil off the baseplate and cut the wires close to the coil. Replace it with the new unit and feed the new leads though the holes in the baseplate.
(more…)

[Read more →]

2006-09 Honda S2000 Base, High-Boost, and YouTune Supercharger Kits Installation

November 18th, 2009 · No Comments

SECTION 1: PRE-INSTALLATION PRECAUTIONS:
Step 1: Remove the negative battery cable. Before removing the battery cable, verify that you have the “anti theft” radio code. It is usually located in your owner’s manual. If you cannot find the radio code, take your car to your local Honda dealer so that they can retrieve the code through the Honda computer network.
Step 2: Jack your car up, or put the car up in the air if you are working in a shop. Support your car with Jack Stands or Ramps if you are working on the ground. Never work under a car without some type of reliable support.
(more…)

[Read more →]

Stator Kit for Triumph 3TA, 5TA, BSA A6 Instructions

November 4th, 2009 · No Comments

FITTING INSTRUCTIONS
Step 1 Remove the original stator & rotor.
Step 2 Fit the new rotor on to the crank shaft locating on to the key (not all models are supplied with a keyway machined into the rotor). Fit the retaining nut but don’t fully tighten if there is no keyway.
Step 3 Position the new stator over the rotor locating on the engine studs using the spacers provided and the original nuts, don’t fully tighten so that the stator can be adjusted if necessary.
Step 4 This will give a maximum total advance of about 350, this is only a guide. Engine tune will affect the actual timing for optimum performance.
(more…)

[Read more →]

Honda 750 Shadow Aero Models Hypercharger Kit Installation

October 29th, 2009 · No Comments

A factory service manual is necessary to perform this installation. Do not attempt to perform this installation if you are not confident in your ability to perform all steps in the procedure, including precise drilling and tapping; consult a trained technician.
Procedure remove the stock aIr cleaner and carburetor
steP 1 Remove the seat, dash panel, and fuel tank; consult your factory service manual for specific instructions on performing this procedure.
steP 2 Remove the air cleaner assembly. Save the clamp securing the rubber manifold to the carburetor, it will be reused later. See PIC.1.
steP 3 Remove the carburetor for re-jetting; consult your factory service manual for specific instructions on removing the carburetor. Prepare the carburetor for re-jetting by removing the top cover, see PIC.2.
(more…)

[Read more →]

Honda TRX450R Installation Procedure

October 29th, 2009 · No Comments

REAR SETUP (45” hose)
STEP 1: Lift the vehicle off the ground with a jack or on a stand. Remove the stock shock absorber from the vehicle. Install the Elka shock absorbers on the vehicle. The banjo bolt must face towards the front of the vehicle with the hose coming out on the left side. The rebound adjuster located at the bottom of the shock should face the rear of the quad for convenient access. The bottom fork of the shock can be turned 180° clockwise if needed.
(more…)

[Read more →]

SuperSprings Model # SSA10 Installation Instructions

October 26th, 2009 · No Comments

Front / Rear & Poly Spring Pads (PSP’s)
The SSA10 springs do NOT have a specific left or right side; however, they do have a specific front / rear side. Position the two-hole shackle to the front and the three-hole shackle to the rear. PLEASE NOTE: Two sets of PSP’s are included with these springs. The larger set is for Ford applications; the smaller set is for GMC and Dodge applications. See page three of these instructions for more details
(more…)

[Read more →]

Rocket Locker Side Rails Installation Instruction

October 25th, 2009 · No Comments

Upon receipt of the Rocket Locker, the casting and the light should already be assembled and wires should be fed thru casting.
Step 1: Feed wires thru hole in the oval gasket.
Step 2: Install Allen head bolts through the hole in Rocket Locker casting, plastic oval gasket, and rubber expander.
Step 3: Install threaded back plate on Allen head bolt. Snugly tighten the back plate against the rubber expander.
Step 4: Remove the tail light lens. To do this, open tailgate and remove the screws that hold the lens in place (refer to picture below). If you are not sure which screws hold the lens in place refer to your owner’s manual on how to replace tail light bulbs. Then release the tabs on the other side of the lens.
(more…)

[Read more →]

1999 Chevrolet Silverado Push Bar Assemblies Installation Instructions

October 25th, 2009 · No Comments

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list.
STEP 2. Read and understand instructions completely before beginning installation.
STEP 3. Determine Driver and Passenger Uprights and Top and Bottom Tubes. (Uprights are positioned so raised side of bolt holes are facing each other and the Tube with the two pierced holes is the Bottom Tube).
(more…)

[Read more →]