Automotive Manual PDF

RSS Feed

The Resources for Automotive

2010 Hyundai Genesis Coupe L4-2.0L Turbo AEM Dryflow Filter Installation Instructions

March 24th, 2010 · No Comments

1. Preparing Vehicle
a. Make sure vehicle is parked on level surface.
b. Set parking brake.
c. If engine has run in the past two hours, let it cool down.
d. Disconnect negative battery terminal.
e. Jack up the front of the vehicle and support using properly rated jack stands.
f. Do not discard stock components after removal of the factory system.
(more…)

[Read more →]

260-302 c.i.d. Small Block Ford Engines Performer and Performer RPM Intake Manifolds Instructions

August 19th, 2009 · No Comments

Edelbrock Performer series intake manifolds are designed for engines operating in the idle to 5500 rpm range. Performer RPM series intake manifolds are designed for engines operating in the 1500-6500 rpm range. Match Performer or Performer RPM intake manifolds with recommended carburetors and additional equipment for even greater performance increases.

EGR SYSTEMS: Edelbrock EGR-equipped Performer manifolds are intended as a direct functionally identical replacement for their O.E.M. counterparts. All exhaust emissions or emissions related stock components are intended to be retained and functional. Non-EGR equipped manifolds will not accept stock EGR (Exhaust Gas Recirculation) equipment. EGR systems are used on most 1972 and later model vehicles. Check local laws for requirements.
(more…)

[Read more →]

Ducati Monster Bobbed License Plate / Signal Relocation Bracket – Redpoint Racing

January 26th, 2009 · No Comments

The relocation bracket is designed to fit all Ducati Monsters within the year ranges of 2000-2004. It may fit other years as well, but I cannot guarantee an exact fit as minor changes have been done throughout the years. The bracket is designed to replace the stock tail light/turn signal/license plate assembly and the rearmost section of the frame on which the stock assembly mounts. It is assumed that the sub frame has already been removed.
(more…)

[Read more →]

2006-2007 6.0L Chevrolet Trailblazer SS Intercooled Supercharger System

November 1st, 2008 · No Comments

We encourage you to read this manual thoroughly before you begin work, for a few reasons: A quick parts check to make certain your kit is complete (see shipper parts list in this manual). If you discover shipping damage or shortage, please call our office immediately. Take a look at exactly what you are going to need in terms of tools, time, and experience.
(more…)

[Read more →]

1993 5.7L LT1 V8 Chevrolet Camaro & Pontiac Firebird Lingenfelter SuperTube Air Intake System

September 15th, 2008 · No Comments

Instructions:
• Read instructions completely before beginning installation.
• Installation should take less than one hour with the proper tools.
• As you remove the stock components, pay careful attention to how things were attached or located. In many cases, the components will be reinstalled in the same way as they were removed.
(more…)

[Read more →]

F-body SuperTube 1993 installation

September 12th, 2008 · No Comments

Installation instructions for the Lingenfelter Performance Engineering (LPE) air intake system for LT1 V-8 equipped 1993 Camaros and Firebirds (#LN0040), 50 state emissions legal (E.O. D-333-15):
Included in the LPE intake system:
• LPE plastic air intake
• K&Nfilter
• plastic block-off plate
• three plastic fasteners
• 3M Dual Lock hook and loop tape (used for Firebird installations only)
(more…)

[Read more →]

Intercooled Supercharger System 2003 & 2004 GM SUV

September 9th, 2008 · No Comments

Our Magna Charger kits are designed for stock engines, with stock components, in good mechanical condition only. Installation on worn or damaged engines is not recommended and may result in engine failure, for which we naturally can’t be responsible . Magna Charger is not responsible for the engine or consequential damages.
(more…)

[Read more →]