1. Raise vehicle and support with jackstands on a stable surface.
Note: Vehicle must be supported with vehicle’s normal weight on rear axle. Do not support vehicle by its trailing arms.
2. Remove only one of the stock lower trailing arms.
3. Install the Edelbrock lower trailing arms with the spherical ball at the rear axle mounting point and the grease fitting on top of the arm. It may be necessary to spread the rear end mounting tabs slightly to install trailing arm.
(more…)
2003-2005 Hummer HII Edelbrock Lower Trailing Arms Installation Instructions
February 12th, 2010 · No Comments
Hummer H3 & H3T 1″ Body Lift Instructions
January 8th, 2010 · No Comments
Your new Daystar body lift kit will allow the installation of 35” tires. Larger tires can be fitted if paired with our 2” torsion bar key kit, and some trimming . The tools needed for installation are on the last page . A list of parts in the kit are under the BOM, verify that you have all parts prior to installing your new Body Lift Kit . Make sure you have all of the proper tools and understand these directions before proceeding. Place Vehicle on level ground. Be sure that the wheels are blocked and the vehicle is in park.
(more…)
2001 CR-V (EX) Cassette Player Installation Instructions
November 15th, 2009 · No Comments
1. If equipped, make sure that you have the anti-theft code for the radio, then write down the frequencies for the preset buttons on the radio.
2. Slide the driver’s seat completely to the rear.
3. Disconnect the negative cable from the battery.
4. Open the glove box. Squeeze the retaining tabs, and remove the stop. Pull the glove box down.
5. Remove the driver’s dashboard lower cover (two self-tapping screws, four retaining clips and one connector).
6. Remove the lower console cover.
(more…)
2009 TSX Front Aero Bumper Installation Instructions
November 14th, 2009 · No Comments
The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE:
• Be extremely careful not to damage the body.
• To prevent damage, rest the front bumper on a blanket or cardboard during the installation.
• Before removing parts, note their locations so that they can be reinstalled in their original locations properly.
(more…)
01-06 Acura MDX Cabin Air Filter Replacement for OEM
November 6th, 2009 · No Comments
1. The filter is located behind the glove compartment. Unscrew the 2 screws at the bottom of the glove box cover to loosen the it. Remove glove box and set it aside.
2. Cut the plastic cover along the dotted lines shown and remove it. Dispose off plastic cover, it is no longer needed. This exposes the metal cross bar under it. Locate and remove 2 additional bolts securing bar. Remove and set it aside.
(more…)
2009 Pilot Fog Lights Installation Instructions
October 31st, 2009 · No Comments
The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1. Make sure you have the anti-theft code for the radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
(more…)
Honda Reflex Windscreen Installation/Removal
October 30th, 2009 · No Comments
Tools/Supplies: Phillips screwdriver, windscreen, maybe glue
Step 1 Remove the 2 screws just below the “HONDA” decal on the front cowl (just below the windscreen).
Step 2 Remove the 2 screws on the pillars that connect the sides of the windscreen to the scooter (1 screw on each pillar, screw heads face driver)
(more…)
Rocket Locker Side Rails Installation Instruction
October 25th, 2009 · No Comments
Upon receipt of the Rocket Locker, the casting and the light should already be assembled and wires should be fed thru casting.
Step 1: Feed wires thru hole in the oval gasket.
Step 2: Install Allen head bolts through the hole in Rocket Locker casting, plastic oval gasket, and rubber expander.
Step 3: Install threaded back plate on Allen head bolt. Snugly tighten the back plate against the rubber expander.
Step 4: Remove the tail light lens. To do this, open tailgate and remove the screws that hold the lens in place (refer to picture below). If you are not sure which screws hold the lens in place refer to your owner’s manual on how to replace tail light bulbs. Then release the tabs on the other side of the lens.
(more…)
Ford Focus Gauge Faces Installation Instructions
August 20th, 2009 · No Comments
This is just a guideline for replacement of the gauge faces on the Ford Focus. Please don’t hold me responsible for anything that may go wrong while following these instructions. These instructions are for entertainment usage only. If you learn something from these instructions, congratulation.
REQUIRED TOOLS:
7mm Hex wrench, socket extensions, Torx T-8 driver, black permanent felt tipped marker.
(more…)
2004 Ford Econoline – 6.0L Diesel Engine Intelligent Lift Interlock System (ILIS501-DC) - Installation Instructions
May 22nd, 2009 · No Comments
To aid in installation, first gain access to the connection points. Remove the lower dash panel below the steering column. Also, gain access to the lift power switch and the lift door switch circuits. These are usually accessible in the front control panel. It is not necessary to cut any Ford wires during the installation of the ILIS wire harness.
(more…)