Automotive Manual PDF

STEP 1: REMOVE PLYWOOD & INVENTORY CONTENTS
Remove the top cover from the canister box and set it aside for later installation.
Remove the canister from the box. Using the 3/8” wrench or socket remove the 2 bolts holding the plywood on the ends of the canister. Use Side Cut Pliers to cut handle retaining straps. DISCARD PLYWOOD PACKAGING AND BOLTS!
Perform a quick inventory to insure all parts are there. Be sure to check inside the small cardboard box for parts.
(more…)

[Read more →]

If your truck does not have a locking tailgate (like provided on many full size Fords, Toyotas and Nissans), you will need to purchase an aftermarket tailgate lock (i.e., Pop’ N Lock, Bully Tailgate Lock, etc.,) to be able to lock the tailgate shut and to secure your truck bed. These lock sets basically replace your existing tailgate handle and convert it into the equivalent of a factory installed locking tailgate. Changing these tailgate lock handles is the equivalent of changing a “door knob” in that you simply loosen the 2 bolts on the inside of the tailgate, remove your non-locking tailgate handle, and replace with one that locks. These install really easily without any drilling and you can buy these at any truck accessories store. Once the cover is closed (and latched), you just simply lock the cover, then lock up your tailgate handle and you now have a really secure trunk!
(more…)

[Read more →]

This truck bed cover is designed for trucks that DO NOT have a bed liner. Trucks that DO have a bed liner may require some minor trimming or modification of the bed liner to insure proper placement for the brackets. Trimming or modification will vary between different brands of bed liners and model of your truck. Remember: Any modifications must be made to the bed liner and NOT to the installation hardware. Modifications to the installation hardware will result in a improper installation and will void your warranty. (See page 9 for do’s & don’ts regarding bed liners.
(more…)

[Read more →]

BRACKET MOUNTING INSTRUCTIONS
Step 1. Remove contents from box and check for damage. Verify all parts against parts list. Read and understand instructions completely before installation.
Step 2. Position and hold template on passenger side for quick latch bracket as shown (See Figure 1). (FOR TOYOTA, NISSAN, CHEVY S-10, GMC up to 94, and MAZDA up to 94 a separate bracket kit must be ordered). Using a center punch, punch each hole. NOTE: If the truck has a bed liner, center punch the bed liner. DO NOT CUT THE BED LINER! Repeat for driver side.
(more…)

[Read more →]

Before you begin installing this top assembly, read all instructions thoroughly. After completing the installation, keep these instructions for further reference. Below are a few tips to make this installation easier.

For a smooth fit:
For ease in installation, the top should be installed at temperatures above 72° F. Below this temperature, the top may contract an inch or more, making it difficult to fit to the vehicle. It is normal for a top to contract and wrinkle when stored in the shipping carton. Within a few days after the installation, the top will relax and the wrinkles will disappear.
(more…)

[Read more →]

Ford Sport Tracs, because of their unique nature, require additional assembly procedures to install the side rails. A set of support brackets and hardware have been included with your TruXedo® kit in place of the clamp assemblies used on standard pickup boxes. These have been especially designed to fit your Sport Trac composite box.
(more…)

[Read more →]

Before beginning installation, familiarize your-self with the installation instructions and the ultrasonic parking assist system components.
To ensure your safety:
A) Make sure your vehicle is in “PARK”.
B) Apply the emergency brake.
C) Read this manual before starting.

CAUTION: It is advisable to disconnect the negative battery cable for 3 minutes before beginning installation, to avoid unintended air bag deployment. Note and record any anti-theft radio codes prior to disconnecting.
(more…)

[Read more →]

Before you begin installing this assembly, read all instructions thoroughly.
For a smooth fit:
For ease in installation, the product should be installed at temperatures above 72° F. Below this temperature, the fabric may contract an inch or more, making it difficult to fit to the vehicle. It is normal for fabric to contract and wrinkle when stored in the shipping carton. Within a few days after the installation, the fabric will relax and the wrinkles will disappear.
(more…)

[Read more →]

INSTALLATION INSTRUCTIONS
1. Inspect liftgate. Report any questionable condition to the carrier that delivered the unit.
2. Place the truck on flat level ground and block the wheels to prevent possible truck movement during liftgate installation.
3. Remove the rear bumper and bumper brackets from the truck. Remove the tailgate, latches and pivots from the rear of the truck box.
(more…)

[Read more →]

OPERATION Tailgate Closed – Inward Position – With the tailgate closed, the Bed X-Tender can be positioned inward to secure small cargo in truck bed. (Figure 1) Tailgate Open – Outward Position – With tailgate open, rotate the Bed X-Tender outward until it rests on the tailgate. (Figure 2) When driving, secure the Bed X-Tender to the tailgate by locking the buckles into the tailgate latches on each side. (Figure 3)
(more…)

[Read more →]