Automotive Manual PDF

1. Check all parts. Read and understand instructions completely before beginning installation. Clean the under side of the frame. Clean out the weld nuts in the frame.
Parts List:
1) Hitch
6) 10mm - 1.25 x 40mm Hex Bolts
6) ł/₈” HD Flatwasher
6) 10mm Lockwashers
2. Remove the exhaust hangers and lower the exhaust to ease installation.
3. Remove the tow hook, four bolts on the passenger side. Remove the rear most bolt behind the tow hook. Return tow hook and bolts to vehicle owner.
(more…)

[Read more →]

Yes, it is somewhat simple and assumes that you’re fairly handy with exhaust systems. However, some of us don’t swap exhaust systems every other Saturday, so I’ll try to provide enough details so that most of you can do this (with the right tools, of course). Okay, the first thing you should do is spray each flange bolt with WD-40, Liquid Wrench, or equivalent stuff. Here’s what the OEM piping/flange connections look like after spraying.
(more…)

[Read more →]

REMOVING FACTORYAIR DAM
1. To remove factory Air Dam, use a 6” long flat blade screwdriver. The rivets are accessed through the bottom of the bumper behind the factory Air Dam.
2. It will be necessary to remove the factory driving lights by removing the two bolts that hold the plastic light brackets to the bumper. Also remove the nut clips from the bumper.
3. Insert the screwdriver blade into the rivet head slots and twist screwdriver to force rivet inserts downward. Once rivet inserts are 1/4” to 1/2” down, grab with fingers or pliers and pull down, completely removing inserts.
4. After all rivets and lights are removed, use the screwdriver from the front side of Air Dam and pry down on the Air Dam to remove it from the bumper.
5. Next remove the plastic rivet clips from the bottom of the bumper by squeezing the clips and pulling down.
(more…)

[Read more →]

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not required, but strongly recommended. If local/state law requires a license plate, license plate relocation kit is available.
3. From underside of vehicle, remove the two bolts holding the driver factory tow hook, then remove tow hook from vehicle. NOTE: This Bull Bar is not compatible with factory tow hooks, so you will not be reinstalling factory tow hooks back onto vehicle.
(more…)

[Read more →]

1) Remove 4 bolts beside tow hooks to remove factory bumper. Retain bolts and tow hooks for use in step 7. ( see figure 1)
2) Remove fog lights from factory bumper keeping plastic pins and adjusting screw assembly in tact for future installation.
3) Remove casing from factory fog lights and discard. Install fog lights to brackets located on backside of new bumper using hardware removed in step 2.
(more…)

[Read more →]

Simple step to front bumber replacement:
1) Remove hood release latch from factory assembly on factory bumper. Set aside and retain factory hardware for future installation.
2) Remove 4 bolts beside tow hooks to remove factory bumper. Retain bolts and tow hooks for use in step 7.
3) Remove fog lights from factory bumper retain plastic pins and adjusting screw assembly for future installation.
(more…)

[Read more →]

H2 Hummer Spare Tire Carrier Mounting Instructions
1. Remove both tow loops from rear bumper with 18 MM socket.
2. Remove hinge plate from packaged swing arm assembly. To aid in positioning and support of hinge plate during installation, insert one M12 X 70MM bolt into a driver’s side tow hook mounting hole. The hinge plate can now be temporarily “hung” on the bolt (head of bolt will fit through hole in hinge plate). The hinge plate should be oriented with hinge boss towards passenger’s side (see Photo 1).
(more…)

[Read more →]

2005 G35 Sedan and Coupe This easy-to-use Quick Reference Guide is intended to provide you with a user-friendly learning experience to quickly acquaint you with your new Infiniti. other features Screw-In Tow Hook (Install Behind the Front License Plate Cover) Refer to section 6 in your Owner’s Manual. DRIVING CONTROLS DRIVING CONTROLS The Quick Reference Guide will help you to more fully appreciate your vehicle’s superior features, unique functions and advanced technology. Refer to the Quick Reference Guide to learn how to personalize your vehicle’s controls and equipment to maximize your driving comfort and convenience. Your vehicle is equipped with a screw-in tow hook for pulling the vehicle forward.
(more…)

[Read more →]